liu.seSearch for publications in DiVA
Change search
Link to record
Permanent link

Direct link
BETA
Zukauskaite, Agne
Alternative names
Publications (10 of 12) Show all publications
Tholander, C., Birch, J., Tasnádi, F., Hultman, L., Palisaitis, J., Persson, P. O., . . . Zukauskaitè, A. (2016). Ab initio calculations and experimental study of piezoelectric YxIn1-xN thin films deposited using reactive magnetron sputter epitaxy. Acta Materialia, 105, 199-206
Open this publication in new window or tab >>Ab initio calculations and experimental study of piezoelectric YxIn1-xN thin films deposited using reactive magnetron sputter epitaxy
Show others...
2016 (English)In: Acta Materialia, ISSN 1359-6454, E-ISSN 1873-2453, Vol. 105, p. 199-206Article in journal (Refereed) Published
Abstract [en]

By combining theoretical prediction and experimental verification we investigate the piezoelectric properties of yttrium indium nitride (YxIn1-xN). Ab initio calculations show that the YxIn1-xN wurtzite phase is lowest in energy among relevant alloy structures for 0≤x≤0.5. Reactive magnetron sputter epitaxy was used to prepare thin films with Y content up to x=0.51. The composition dependence of the lattice parameters observed in the grown films is in agreement with that predicted by the theoretical calculations confirming the possibility to synthesize a wurtzite solid solution. An AlN buffer layer greatly improves the crystalline quality and surface morphology of subsequently grown YxIn1-xN films. The piezoelectric response in films with x=0.09 and x=0.14 is observed using piezoresponse force microscopy. Theoretical calculations of the piezoelectric properties predict YxIn1−xN to have comparable piezoelectric properties to ScxAl1-xN.

Place, publisher, year, edition, pages
Elsevier, 2016
Keyword
YInN, Thin films, Sputter deposition, Piezoelectricity, Ab initio calculations
National Category
Condensed Matter Physics Materials Chemistry Inorganic Chemistry Other Materials Engineering Manufacturing, Surface and Joining Technology
Identifiers
urn:nbn:se:liu:diva-125918 (URN)10.1016/j.actamat.2015.11.050 (DOI)000370086500023 ()
Available from: 2016-03-08 Created: 2016-03-08 Last updated: 2017-11-30Bibliographically approved
Ben Sedrine, N., Zukauskaite, A., Birch, J., Jensen, J., Hultman, L., Schoeche, S., . . . Darakchieva, V. (2015). Infrared dielectric functions and optical phonons of wurtzite YxAl1-xN (0 less than= x less than= 0.22). Journal of Physics D: Applied Physics, 48(41), 415102
Open this publication in new window or tab >>Infrared dielectric functions and optical phonons of wurtzite YxAl1-xN (0 less than= x less than= 0.22)
Show others...
2015 (English)In: Journal of Physics D: Applied Physics, ISSN 0022-3727, E-ISSN 1361-6463, Vol. 48, no 41, p. 415102-Article in journal (Refereed) Published
Abstract [en]

YAlN is a new member of the group-III nitride family with potential for applications in next generation piezoelectric and light emitting devices. We report the infrared dielectric functions and optical phonons of wurtzite (0001) YxAl1-xN epitaxial films with 0 less than= x less than= 0.22. The films are grown by magnetron sputtering epitaxy on c-plane Al2O3 and their phonon properties are investigated using infrared spectroscopic ellipsometry and Raman scattering spectroscopy. The infrared-active E-1(TO) and LO, and the Raman active E-2 phonons are found to exhibit one-mode behavior, which is discussed in the framework of the MREI model. The compositional dependencies of the E-1(TO), E-2 and LO phonon frequencies, the high-frequency limit of the dielectric constant, epsilon(infinity), the static dielectric constant, epsilon(0), and the Born effective charge Z(B) are established and discussed.

Place, publisher, year, edition, pages
IOP PUBLISHING LTD, 2015
Keyword
YAlN; phonons; infrared dielectric function
National Category
Physical Sciences Chemical Sciences
Identifiers
urn:nbn:se:liu:diva-122192 (URN)10.1088/0022-3727/48/41/415102 (DOI)000362007100004 ()
Note

Funding Agencies|Swedish Research Council (VR) [2013-5580]; Swedish Governmental Agency for Innovation Systems (VINNOVA) [2011-03486]; Swedish Foundation for Strategic Research (SSF) [2012FFL12-0181]; National Science Foundation [MRSEC DMR-0820521, EPS-1004094]; Stiftelsen Lars Hiertas Minne [FO2013-0587]; [RECI/FIS-NAN/0183/2012 (FCOMP-01-0124-FEDER-027494)]

Available from: 2015-10-26 Created: 2015-10-23 Last updated: 2017-12-01
Zukauskaite, A., Broitman, E., Sandström, P., Hultman, L. & Birch, J. (2015). Nanoprobe Mechanical and Piezoelectric Characterization of ScxAl1-xN(0001) Thin Films. Physica Status Solidi (a) applications and materials science, 212(3), 666-673
Open this publication in new window or tab >>Nanoprobe Mechanical and Piezoelectric Characterization of ScxAl1-xN(0001) Thin Films
Show others...
2015 (English)In: Physica Status Solidi (a) applications and materials science, ISSN 1862-6300, E-ISSN 1862-6319, Vol. 212, no 3, p. 666-673Article in journal (Refereed) Published
Abstract [en]

Nanoindentation with in-situ electrical characterization was used to characterize piezoelectric scandium aluminum nitride (ScxAl1-xN) thin films with Sc contents up to x=0.3. The films were prepared by reactive magnetron sputtering using Al2O3 substrates with TiN seed layer/bottom electrodes at a substrate temperature of 400 °C. X-ray diffraction shows c-axis oriented wurtzite ScxAl1-xN, where the crystal quality decreases with increasing x. Piezoresponse force microscopy in mapping mode shows a single piezoelectric polarization phase in all samples. The hardness and decreases from 17 GPa in AlN to 11 GPa in Sc0.3Al0.7N, while reduced elastic modulus decreases from 265 GPa to 224 GPa, respectively. Both direct and converse piezoelectric measurements are demonstrated by first applying the load and generating the voltage and later by applying the voltage and measuring film displacement using a conductive boron doped nanoindenter tip. The Sc0.2Al0.8N films exhibit an increase in generated voltage by 15% in comparison to AlN and a correspondingly larger displacement upon applied voltage, comparable to results obtained by double beam interferometry and piezoresponse force microscopy.

 

Place, publisher, year, edition, pages
John Wiley & Sons, 2015
National Category
Physical Sciences
Identifiers
urn:nbn:se:liu:diva-103830 (URN)10.1002/pssa.201431634 (DOI)000351530800029 ()
Note

On the day of the defence date of the Ph.D. Thesis, the status of this article was Manuscript.

Available from: 2014-01-29 Created: 2014-01-29 Last updated: 2017-12-06Bibliographically approved
Žukauskaitė, A., Tholander, C., Tasnádi, F., Alling, B., Pališaitis, J., Lu, J., . . . Birch, J. (2015). Stabilization of Wurtzite Sc0.4Al0.6N in Pseudomorphic Epitaxial ScxAl1-xN/InyAl1-yN Superlattices. Acta Materialia, 94, 101-110
Open this publication in new window or tab >>Stabilization of Wurtzite Sc0.4Al0.6N in Pseudomorphic Epitaxial ScxAl1-xN/InyAl1-yN Superlattices
Show others...
2015 (English)In: Acta Materialia, ISSN 1359-6454, E-ISSN 1873-2453, Vol. 94, p. 101-110Article in journal (Refereed) Published
Abstract [en]

Pseudomorphic stabilization in wurtzite ScxAl1-xN/AlN and ScxAl1-xN/InyAl1-yN superlattices (x=0.2, 0.3, and 0.4; y=0.2-0.72), grown by reactive magnetron sputter epitaxy was investigated. X-ray diffraction and transmission electron microscopy show that in ScxAl1-xN/AlN superlattices the compressive biaxial stresses due to positive lattice mismatch in Sc0.3Al0.7N and Sc0.4Al0.6N lead to loss of epitaxy, although the structure remains layered. For the negative lattice mismatched In-rich ScxAl1-xN/InyAl1-yN superlattices a tensile biaxial stress promotes the stabilization of wurtzite ScxAl1-xN even for the highest investigated concentration x=0.4. Ab initio calculations with fixed in-plane lattice parameters show a reduction in mixing energy for wurtzite ScxAl1-xN under tensile stress when x≥0.375 and support the experimental results.

Place, publisher, year, edition, pages
Elsevier, 2015
National Category
Natural Sciences
Identifiers
urn:nbn:se:liu:diva-103831 (URN)10.1016/j.actamat.2015.04.033 (DOI)000357143500010 ()
Available from: 2014-01-29 Created: 2014-01-29 Last updated: 2017-12-06Bibliographically approved
Žukauskaitė, A. (2014). Metastable ScAlN and YAlN Thin Films Grown by Reactive Magnetron Sputter Epitaxy. (Doctoral dissertation). Linköping: Linköping University Electronic Press
Open this publication in new window or tab >>Metastable ScAlN and YAlN Thin Films Grown by Reactive Magnetron Sputter Epitaxy
2014 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Metastable ScxAl1-xN and YxAl1-xN thin films were deposited in an ultra high vacuum system using reactive magnetron sputter epitaxy from elemental Al, Sc, and Y targets in Ar/N2 gas mixture. Their structural, electrical, optical, mechanical, and piezoelectrical properties were investigated by using the transmission electron microscopy, x-ray diffraction, spectroscopic ellipsometry, I-V and C-V measurements, nanoindentation, and two different techniques for piezoelectric characterization: piezoresponse force microscopy and double beam interferometry.

Compared to AlN, improved electromechanical coupling and increase in piezoelectric response was found in ScxAl1-xN/TiN/Al2O3 structures with Sc content up to x=0.2. Decreasing the growth temperature down to 400 °C improved the microstructure and crystalline quality of the material. Microstructure of the films had a stronger influence on piezoelectric properties than the crystalline quality, which affected the leakage currents. When x was increased from x=0 to x=0.3, the hardness and reduced Young’s modulus Er showed a decrease from 17 GPa to 11 GPa, and 265 GPa down to 224 GPa, respectively. In ScxAl1-xN/InyAl1-yN superlattices, ScxAl1-xN layers negative lattice mismatched to In-rich InyAl1-yN were found to be stable at higher Sc concentration (x=0.4) than lattice-matched or positive lattice mismatched layers, confirmed by first principle (ab initio) calculations using density-functional formalism.

Al-rich YxAl1-xN thin films were synthesized and reported for the first time. Formation of solid solution was observed up to x=0.22 and an increase in growth temperature up to 900°C improved the crystalline quality of the YxAl1-xN films. The band gap of YxAl1-xN decreased from 6.2 eV for AlN down to 4.5 eV (x=0.22) and was shown to follow Vegard’s rule. Refractive indices and extinction coefficients were also determined. Lattice constants of wurtzite YxAl1-xN measured experimentally are in good agreement with theoretical predictions obtained through ab initio calculations. The mixing enthalpy

Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2014. p. 64
Series
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1564
National Category
Physical Sciences
Identifiers
urn:nbn:se:liu:diva-103832 (URN)10.3384/diss.diva-103832 (DOI)978-91-7519-434-9 (ISBN)
Public defence
2014-02-21, Planck, Fysikhuset, Campus Valla, Linköpings universitet, Linköping, 10:15 (English)
Opponent
Supervisors
Available from: 2014-01-29 Created: 2014-01-29 Last updated: 2016-08-31Bibliographically approved
Ben Sedrine, N., Zukauskaite, A., Birch, J., Hultman, L. & Darakchieva, V. (2013). Bandgap Engineering and Optical Constants of YxAl1-xN Alloys. Japanese Journal of Applied Physics, 52(8)
Open this publication in new window or tab >>Bandgap Engineering and Optical Constants of YxAl1-xN Alloys
Show others...
2013 (English)In: Japanese Journal of Applied Physics, ISSN 0021-4922, E-ISSN 1347-4065, Vol. 52, no 8Article in journal (Refereed) Published
Abstract [en]

We study wurtzite Yx Al1-xN (0 andlt;= x andlt;= 0:22) films with (0001) orientation deposited by magnetron sputtering epitaxy on Si(100) substrates and we determine the alloys band gap energies and optical constants. Room temperature spectroscopic ellipsometry (SE) is employed in the energy range from 1 to 6.3 eV, and data modeling based on the standard dielectric function model is used. As a result of the SE data analysis the Yx Al1-xN refractive index and extinction coefficient are determined. The band gap of Yx Al1-xN is found to decrease linearly from 6.2 eV (x=0) down to 4.5 eV (x=0:22). We further observe an increase of the refractive index with increasing Y content; from 1.93 to 2.20 (at 2 eV) for x=0 and 0.22, respectively, reflecting the increase in material density.

Place, publisher, year, edition, pages
Japan Society of Applied Physics, 2013
National Category
Engineering and Technology
Identifiers
urn:nbn:se:liu:diva-98153 (URN)10.7567/JJAP.52.08JM02 (DOI)000323883100159 ()
Note

Funding Agencies|FCT|REF:SFRH/BPD/66818/2009|Swedish Research Council (VR)|2010-3848|Linko "ping Linnaeus Initiative on Nanoscale Functional Materials (LiLiNFM)||Swedish Governmental Agency for Innovation Systems (VINNOVA)|2011-03486|

Available from: 2013-09-30 Created: 2013-09-30 Last updated: 2017-12-06
Žukauskaitė, A. (2012). Metastable YAlN and ScAlN thin films: growth and characterization. (Licentiate dissertation). Linköping: Linköping University Electronic Press
Open this publication in new window or tab >>Metastable YAlN and ScAlN thin films: growth and characterization
2012 (English)Licentiate thesis, comprehensive summary (Other academic)
Abstract [en]

ScxAl1-xN and YxAl1-xN thin films were deposited in a ultra high vacuum system using reactive magnetron co-sputtering from elemental Al, Sc and Y targets in Ar/N2. Their mechanical, electrical, optical, and piezoelectrical properties were investigated with the help of transmission electron microscopy, xray diffraction, ellipsometry, I-V and C-V measurements, and two different techniques for piezoelectric characterization: piezoresponse force microscopy and double beam interferometry. Compared to AlN, improved electromechanical coupling and increase in piezoelectric response was found in ScxAl1-xN/TiN/Al2O3 structures with Sc content up to x=0.2. Microstructure of the films had a stronger influence on piezoelectric properties than the crystalline quality, which affected the leakage currents. YxAl1-xN thin films show a formation of solid solution up to x=0.22. Lattice constants obtained experimentally are in good agreement with theoretical predictions obtained through first principle (ab initio) calculations using density-functional formalism. The mixing enthalpy for wurtzite, cubic, and layered hexagonal phases of the YxAl1-xN system was also calculated.

Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2012. p. 46
Series
Linköping Studies in Science and Technology. Thesis, ISSN 0280-7971 ; 1524
National Category
Natural Sciences
Identifiers
urn:nbn:se:liu:diva-76474 (URN)10.3384/lic.diva-76474 (DOI)LIU-TEK-LIC-2012:9 (Local ID)978-91-7519-934-4 (ISBN)LIU-TEK-LIC-2012:9 (Archive number)LIU-TEK-LIC-2012:9 (OAI)
Supervisors
Available from: 2012-04-10 Created: 2012-04-10 Last updated: 2016-08-31Bibliographically approved
Žukauskaitė, A., Wingqvist, G., Pališaitis, J., Jensen, J., Persson, P. O. Å., Matloub, R., . . . Hultman, L. (2012). Microstructure and Dielectric Properties of Piezoelectric Magnetron Sputtered w-ScxAl1-xN thin films. Journal of Applied Physics, 111(9), 093527
Open this publication in new window or tab >>Microstructure and Dielectric Properties of Piezoelectric Magnetron Sputtered w-ScxAl1-xN thin films
Show others...
2012 (English)In: Journal of Applied Physics, ISSN 0021-8979, E-ISSN 1089-7550, Vol. 111, no 9, p. 093527-Article in journal (Refereed) Published
Abstract [en]

Piezoelectric wurtzite ScxAl1-xN (x=0, 0.1, 0.2, 0.3) thin films were epitaxially grown by reactive magnetron co-sputtering from elemental Sc and Al targets. Al2O3(0001) wafers with TiN(111) seed and electrode layers were used as substrates. X-ray diffraction shows that an increase in the Sc content results in the degradation of the crystalline quality. Samples grown at 400 °C possess true dielectric behavior with quite low dielectric losses and the leakage current is negligible. For ScAlN samples grown at 800 °C, the crystal structure is poor and leakage current is high. Transmission electron microscopy with energy dispersive x-ray spectroscopy mapping shows a mass separation into ScN-rich and AlN-rich domains for x≥0.2 when substrate temperature is increased from 400 to 800 °C. The piezoelectric response of epitaxial ScxAl1-xN films measured by piezoresponse force microscopy and double beam interferometry shows up to 180% increase by the addition of Sc up to x=0.2 independent of substrate temperature, in good agreement with previous theoretical predictions based on density-functional theory.

Place, publisher, year, edition, pages
American Institute of Physics (AIP), 2012
National Category
Natural Sciences
Identifiers
urn:nbn:se:liu:diva-76471 (URN)10.1063/1.4714220 (DOI)000304109900044 ()
Available from: 2012-04-10 Created: 2012-04-10 Last updated: 2017-12-07Bibliographically approved
Žukauskaitė, A., Tholander, C., Pališaitis, J., Persson, P. O. Å., Darakchieva, V., Ben Sedrine, N., . . . Hultman, L. (2012). YxAl1-xN Thin Films. Journal of Physics D: Applied Physics, 45(42), 422001
Open this publication in new window or tab >>YxAl1-xN Thin Films
Show others...
2012 (English)In: Journal of Physics D: Applied Physics, ISSN 0022-3727, E-ISSN 1361-6463, Vol. 45, no 42, p. 422001-Article in journal (Refereed) Published
Abstract [en]

Reactive magnetron sputtering was used to deposit YxAl1-xN thin films, 0≤x≤0.22, onto Al2O3(0001) and Si(100) substrates. X-ray diffraction and analytical electron microscopy show that the films are solid solutions. Lattice constants are increasing with Y concentration, in agreement with ab initio calculations. Spectroscopic ellipsometry measurements reveal a band gap decrease from 6.2 eV (x=0) down to 4.9 eV (x=0.22). Theoretical investigations within the special quasirandom structure approach show that the wurtzite structure has the lowest mixingenthalpy for 0≤x≤0.75.

Place, publisher, year, edition, pages
Institute of Physics Publishing (IOPP), 2012
National Category
Natural Sciences
Identifiers
urn:nbn:se:liu:diva-76472 (URN)10.1088/0022-3727/45/42/422001 (DOI)000309766700001 ()
Note

funding agencies|Linkoping Linnaeus Initiative on Nanoscale Functional Materials (LiLiNFM)||Swedish Research Council (VR)|349-2008-6582|FCT Portugal|SFRH/BPD/66818/2009|VR|2010-3848|Swedish Governmental Agency for Innovation Systems (VINNOVA)|2011-03486|

Available from: 2012-04-10 Created: 2012-04-10 Last updated: 2017-12-07Bibliographically approved
Kerdsongpanya, S., Van Nong, N., Pryds, N., Zukauskaite, A., Jensen, J., Birch, J., . . . Eklund, P. (2011). Anomalously high thermoelectric power factor in epitaxial ScN thin films. Applied Physics Letters, 99(23), 232113
Open this publication in new window or tab >>Anomalously high thermoelectric power factor in epitaxial ScN thin films
Show others...
2011 (English)In: Applied Physics Letters, ISSN 0003-6951, E-ISSN 1077-3118, Vol. 99, no 23, p. 232113-Article in journal (Refereed) Published
Abstract [en]

Thermoelectric properties of ScN thin films grown by reactive magnetron sputtering on Al2O3(0001) wafers are reported. X-ray diffraction and elastic recoil detection analyses show that the composition of the films is close to stoichiometry with trace amounts (similar to 1 at. % in total) of C, O, and F. We found that the ScN thin-film exhibits a rather low electrical resistivity of similar to 2.94 mu Omega m, while its Seebeck coefficient is approximately similar to-86 mu V/K at 800 K, yielding a power factor of similar to 2.5 x 10(-3) W/mK(2). This value is anomalously high for common transition-metal nitrides.

Place, publisher, year, edition, pages
American Institute of Physics (AIP), 2011
National Category
Engineering and Technology
Identifiers
urn:nbn:se:liu:diva-75290 (URN)10.1063/1.3665945 (DOI)000298006100041 ()
Note
Funding Agencies|Swedish Research Council (VR)|621-2009-5258|Available from: 2012-02-27 Created: 2012-02-24 Last updated: 2017-12-07
Organisations

Search in DiVA

Show all publications