liu.seSearch for publications in DiVA
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Additively Manufactured Inconel 718: Microstructures and Mechanical Properties
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
2018 (engelsk)Licentiatavhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Additive manufacturing (AM), also known as 3D printing, has gained significant interest in aerospace, energy, automotive and medical industries due to its capabilities of manufacturing components that are either prohibitively costly or impossible to manufacture by conventional processes. Among the various additive manufacturing processes for metallic components, electron beam melting (EBM) and selective laser melting (SLM) are two of the most widely used powder bed based processes, and have shown great potential for manufacturing high-end critical components, such as turbine blades and customized medical implants. The futures of the EBM and SLM are doubtlessly promising, but to fully realize their potentials there are still many challenges to overcome.

Inconel 718 (IN718) is a nickel-base superalloy and has impressive combination of good mechanical properties and low cost. Though IN718 is being mostly used as a turbine disk material now, the initial introduction of IN718 was to overcome the poor weldability of superalloys in 1960s, since sluggish precipitation of strengthening phases λ’/λ’’ enables good resistance to strain-age cracking during welding or post weld heat treatment. Given the similarity between AM and welding processes, IN718 has been widely applied to the metallic AM field to facilitate the understandings of process-microstructure-property relationships.

The work presented in this licentiate thesis aims to better understand microstructures and mechanical properties EBM and SLM IN718, which have not been systematically investigated. Microstructures of EBM and SLM IN718 have been characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and correlated with the process conditions. Monotonic mechanical properties (e.g., Vickers microhardness and tensile properties) have also been measured and rationalized with regards to the microstructure evolutions before and after heat treatments.

For EBM IN718, the results show the microstructure is not homogeneous but dependant on the location in the components, and the anisotropic mechanical properties are probably attributed to alignment of porosities rather than texture. Post heat treatment can slightly increase the mechanical strength compared to the as-manufactured condition but does not alter the anisotropy. SLM IN718 shows significantly different microstructure and mechanical properties to EBM IN718. The as-manufactured SLM IN718 has very fine dendritic microstructure and Laves phases in the interdendrites, and is “work-hardened” by the residual strains and dislocations present in the material. Mechanical properties are different between horizontally and vertically built samples, and heat treatment can minimize this difference. Results from this licentiate thesis provide the basis for the further research on the cyclic mechanical properties of EBM and SLM IN718, which would be the focus of following phase of the Ph.D. research.

sted, utgiver, år, opplag, sider
Linköping: Linköping University Electronic Press, 2018. , s. 69
Serie
Linköping Studies in Science and Technology. Licentiate Thesis, ISSN 0280-7971 ; 1798
HSV kategori
Identifikatorer
URN: urn:nbn:se:liu:diva-144491DOI: 10.3384/lic.diva-144491ISBN: 9789176853832 (tryckt)OAI: oai:DiVA.org:liu-144491DiVA, id: diva2:1177201
Veileder
Merknad

Information about opponent and seminar are missing.

Tilgjengelig fra: 2018-01-24 Laget: 2018-01-24 Sist oppdatert: 2019-10-12bibliografisk kontrollert
Delarbeid
1. Microstructure and Anisotropic Mechanical Properties of EBM Manufactued Inconel 718 and Effects of Post Heat Treatment
Åpne denne publikasjonen i ny fane eller vindu >>Microstructure and Anisotropic Mechanical Properties of EBM Manufactued Inconel 718 and Effects of Post Heat Treatment
2017 (engelsk)Inngår i: Materials Science & Engineering: A, ISSN 0921-5093, E-ISSN 1873-4936, Vol. 693, s. 151-163Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Materials manufactured with electron beam melting (EBM) have different microstructures and properties to those manufactured using conventional manufacturing methods. A detailed study of the microstructures and mechanical properties of Inconel 718 manufactured with EBM was performed in both as-manufactured and heat-treated conditions. Different scanning strategies resulted in different microstructures: contour scanning led to heterogeneous grain morphologies and weak texture, while hatch scanning resulted in predominantly columnar grains and strong 〈001〉 building direction texture. Precipitates in the as-manufactured condition included γ′, γ″, δ  , TiN and NbC, among which considerable amounts of γ″ yielded relatively high hardness and strength. Strong texture, directionally aligned pores and columnar grains can lead to anisotropic mechanical properties when loaded in different directions. Heat treatments increased the strength and led to different δ precipitation behaviours depending on the solution temperatures, but did not remove the anisotropy. Ductility seemed to be not significantly affected by heat treatment, but instead by the NbC and defects inherited from manufacturing. The study thereby might provide the potential processing windows to tailor the microstructure and mechanical properties of EBM IN718.

sted, utgiver, år, opplag, sider
Elsevier, 2017
Emneord
Electron beam melting; Nickel based superalloy; Microstructure; Anisotropy; Mechanical properties; Heat treatments
HSV kategori
Identifikatorer
urn:nbn:se:liu:diva-137289 (URN)10.1016/j.msea.2017.03.085 (DOI)000401384400018 ()2-s2.0-85016252903 (Scopus ID)
Merknad

Funding agencies: Sandvik Machining Solutions AB in Sandviken, Sweden; Faculty Grant SFO-MAT-LiU at Linkoping University [2009-00971]; Chinese Scholarship Council; Agora Materiae

Tilgjengelig fra: 2017-05-10 Laget: 2017-05-10 Sist oppdatert: 2019-11-07bibliografisk kontrollert

Open Access i DiVA

Additively Manufactured Inconel 718: Microstructures and Mechanical Properties(945 kB)1045 nedlastinger
Filinformasjon
Fil FULLTEXT02.pdfFilstørrelse 945 kBChecksum SHA-512
9b584081bfbcccac5b8b94c13486ff3eecdca92fda95c9aec053bf484c79d20fa2f25567bcb22e5d83d5a0b3eb5008b38591770c47acbb823b181100db4f5959
Type fulltextMimetype application/pdf
omslag(4434 kB)80 nedlastinger
Filinformasjon
Fil COVER01.pdfFilstørrelse 4434 kBChecksum SHA-512
00be62d50c573464282f85673adc3d914882cb2455c6b65f2b8abf455c86b3c10b521d65b0e03c8ba7cec62c6ffd473461d8964184a8616f2129afbe2990b203
Type coverMimetype application/pdf
Bestill online >>

Andre lenker

Forlagets fulltekst

Personposter BETA

Deng, Dunyong

Søk i DiVA

Av forfatter/redaktør
Deng, Dunyong
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 1045 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

doi
isbn
urn-nbn

Altmetric

doi
isbn
urn-nbn
Totalt: 2457 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf