liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of fibre coating and geometry on the tensile properties of hybrid carbon nanotube coated carbon fibre reinforced composite
Department of Chemical and Environmental Engineering, Faculty of Engineering, University Putra Malaysia, Selangor, Malaysia.
Department of Chemical and Environmental Engineering, Faculty of Engineering, University Putra Malaysia, Selangor, Malaysia; Nanotechnology and Nanomaterials Group, Materials Processing and Technology Laboratory, Institute of Advanced Technology, University Putra Malaysia, Selangor, Malaysia.
Nanotechnology and Nanomaterials Group, Materials Processing and Technology Laboratory, Institute of Advanced Technology, University Putra Malaysia, Selangor, Malaysia.
Department of Chemical and Environmental Engineering, Faculty of Engineering, University Putra Malaysia, Selangor, Malaysia; Nanotechnology and Nanomaterials Group, Materials Processing and Technology Laboratory, Institute of Advanced Technology, University Putra Malaysia, Selangor, Malaysia.
2014 (Engelska)Ingår i: Materials & Design, ISSN 0261-3069, Vol. 54, s. 660-669Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Hierarchically structured hybrid composites are ideal engineered materials to carry loads and stresses due to their high in-plane specific mechanical properties. Growing carbon nanotubes (CNTs) on the surface of high performance carbon fibres (CFs) provides a means to tailor the mechanical properties of the fibre–resin interface of a composite. The growth of CNT on CF was conducted via floating catalyst chemical vapor deposition (CVD). The mechanical properties of the resultant fibres, carbon nanotube (CNT) density and alignment morphology were shown to depend on the CNT growth temperature, growth time, carrier gas flow rate, catalyst amount, and atmospheric conditions within the CVD chamber. Carbon nanotube coated carbon fibre reinforced polypropylene (CNT-CF/PP) composites were fabricated and characterized. A combination of Halpin–Tsai equations, Voigt–Reuss model, rule of mixture and Krenchel approach were used in hierarchy to predict the mechanical properties of randomly oriented short fibre reinforced composite. A fractographic analysis was carried out in which the fibre orientation distribution has been analyzed on the composite fracture surfaces with Scanning Electron Microscope (SEM) and image processing software. Finally, the discrepancies between the predicted and experimental values are explained.

Ort, förlag, år, upplaga, sidor
Elsevier, 2014. Vol. 54, s. 660-669
Nyckelord [en]
Hybrid composite, Carbon nanotubes, Mechanical property, Chemical vapor deposition, Fibre orientation distribution
Nationell ämneskategori
Annan materialteknik
Identifikatorer
URN: urn:nbn:se:liu:diva-151324DOI: 10.1016/j.matdes.2013.08.063ISI: 000328690400083Scopus ID: 2-s2.0-84884392759OAI: oai:DiVA.org:liu-151324DiVA, id: diva2:1248851
Tillgänglig från: 2018-09-17 Skapad: 2018-09-17 Senast uppdaterad: 2018-09-27Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Sök vidare i DiVA

Av författaren/redaktören
Aziz, Shazed
I samma tidskrift
Materials & Design
Annan materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 93 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf