liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Undersökning av svetsförband med avseende på svetsgeometri, diskontinuiteter och blästring med stålkulor
Linköpings universitet, Institutionen för konstruktions- och produktionsteknik.
2006 (Svenska)Självständigt arbete på grundnivå (yrkesexamen), 20 poäng / 30 hpStudentuppsatsAlternativ titel
An Examination of Welded Joints Regarding Weld Geometry, Weld Discontinuities and the Effects of Shot Peening (Engelska)
Abstract [en]

Breakdowns of welded structures are usually a consequence of fatigue loading. Fatigue fractures are commonly initiated in the region close to the weld toe but can also initiate from the weld root and from discontinuities inside the weld. The purpose of this investigation was to examine the weld quality of welded joints produced at Volvo Wheel Loaders factory in Arvika. The goal of the investigation is to give a clearer insight regarding factors influencing the fatigue strength of the welded joints and thereby give a better foundation for fatigue strength calculations.

The investigation is including examination of the weld geometry, weld discontinuities and the effects of shot peening. Mainly three different methods for collecting test data have been used: Plastic replicas cast on the weld profile, weld specimens from a rear frame belonging to a wheel loader of model L110E/120E and Almen testing of the shot peening.

The results showed that it is not possible to control even transition between the weld material and the base material without after treatment. The most frequent reason why the welded joints did not fulfill the demands in the Volvo Corporate Standard was leg deviation outside the acceptable limit. The most frequent weld defect was lack of fusion inside the weld. The occurrence of this defect was overrepresented in butt welds. The results also showed that the fatigue enhancing effects of shot peening are with today’s process just being used to a minor degree.

Ort, förlag, år, upplaga, sidor
Institutionen för konstruktions- och produktionsteknik , 2006. , s. 106
Nyckelord [sv]
Svetsteknologi, utmattningshållfatshet
Nationell ämneskategori
Tillförlitlighets- och kvalitetsteknik
Identifikatorer
URN: urn:nbn:se:liu:diva-5316ISRN: LITH-IKP-EX--05/2315--SEOAI: oai:DiVA.org:liu-5316DiVA, id: diva2:21258
Uppsök
teknik
Handledare
Examinatorer
Tillgänglig från: 2006-02-06 Skapad: 2006-02-06

Open Access i DiVA

fulltext(3163 kB)7453 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 3163 kBChecksumma SHA-1
f6910540a3a4495a6af1955d85a3b0d57850e62964101132d9715b56cd320567643fee02
Typ fulltextMimetyp application/pdf

Av organisationen
Institutionen för konstruktions- och produktionsteknik
Tillförlitlighets- och kvalitetsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 7454 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 793 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf