liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Modelling the Effect of Graphite Morphology on the Modulus of Elasticity in Cast Irons
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska högskolan.
2004 (Engelska)Ingår i: International Journal of Cast Metals Research, ISSN 1364-0461, Vol. 17, nr 5, s. 271-279Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Nine grades of pearlitic cast iron containing different graphite morphologies (from flake, compacted and spheroidal) have been studied. The parameters investigated include the graphite aspect ratio, nodularity, graphite size and modulus of elasticity. These parameters have been correlated and compared with different existing bound and model equations. It has been found that the modulus of elasticity of the graphite phase increases as the aspect ratio and nodularity of the graphite increases, i.e.flake graphite gives a lower modulus of elasticity than spheroidal graphite. The experimental values of the modulus of elasticity show good agreement to bound and model equations, although flake graphite cast irons show higher deviation from the modelled values. An equation for the correlation between the graphite modulus of elasticity and the nodularity is presented. Introducing this linear correlation into an existing model for the determination of the effective modulus of elasticity gives a continuous function, including all grades of cast irons, with a very good agreement with experimental values. The modulus of elasticity of cast irons can be accurately predicted from both bound and especially model equations, using the aspect ratio and nodularity of the contained graphite particles. The fit is improved by using a modulus of elasticity of the graphite phase that is based on the graphite morphology, considering that the modulus of elasticity of the graphite is different in the basal and prismatic planes.

Ort, förlag, år, upplaga, sidor
2004. Vol. 17, nr 5, s. 271-279
Nyckelord [en]
Cast iron, Modulus of elasticity, Graphite morphology, Graphite aspect ratio, Compacted graphite, Flake graphite, Spheroidal graphite, Modelling
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
URN: urn:nbn:se:liu:diva-14417DOI: 10.1179/136404604225022694OAI: oai:DiVA.org:liu-14417DiVA, id: diva2:23469
Tillgänglig från: 2007-04-20 Skapad: 2007-04-20 Senast uppdaterad: 2013-11-28
Ingår i avhandling
1. Influences of the Graphite Phase on Elastic and Plastic Deformation Behaviour of Cast Irons
Öppna denna publikation i ny flik eller fönster >>Influences of the Graphite Phase on Elastic and Plastic Deformation Behaviour of Cast Irons
2007 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The amount and morphology of the graphite phase largely controls the resulting properties of cast iron. For instance, in flake graphite cast irons the mechanical properties are low while the thermal conductivity is high. This is in contrast with spheroidal graphite cast irons where the mechanical properties are high and the thermal conductivity is low. These differences are due to the different graphite morphologies and must be accounted for in the design work and material selection of cast iron components. In this work the influence of the graphite phase on the elastic and plastic deformation behaviour of cast irons has been studied.

The material grades studied originate from castings for marine diesel engine piston rings with different chemical analyses. Two groups of pearlitic cast iron materials were studied; one with differences in graphite morphology and one with grey irons that differed in graphite content. For these different material grades the mechanical properties were correlated to microstructural parameters. In addition to standard uniaxial tensile tests, acoustic emission measurements were used for the study of deformation.

When studying the modulus of elasticity of the cast iron it was found that the modulus of elasticity of the inherent graphite phase depends on the roundness of the graphite particles and is due to the strong anisotropy of the graphite phase. A linear correlation between nodularity and the modulus of elasticity of the graphite phase was derived. This correlation made it possible to account for the anisotropy of the graphite phase in the model used. By applying the linear function when modelling the effective modulus of elasticity, a high accuracy between experimental and theoretical values was achieved.

Another factor affecting the elastic response when subjecting a cast iron component to tensile load was found to be the plastic deformation that actually occurs at very low strains for all of the studied cast iron grades. It was observed that the plastic deformation in the low strain elastic region, quantified by using acoustic emission measurements, increased linearly with decreasing modulus of elasticity. These measurements showed that the amount of plastic deformation in the elastic region was largely controlled by the graphite morphology. It was concluded that as the roundness of the graphite particles increases, the plastic deformation activity in the elastic region decreases.

The plastic deformation activity continued linearly into the pronounced plastic region of the tensile tests. A decrease in roundness or increase in graphite fraction resulted in an increase of the amount of plastic deformation and the strain hardening exponent. A

dependence between strength coefficient and graphite fraction was observed. Models for the flow curves for pearlitic cast irons were developed and shown to accurately reproduce the observed experimental curves.

The surveys performed and conclusions from this thesis will be helpful in the design of new cast iron materials.

Ort, förlag, år, upplaga, sidor
Institutionen för ekonomisk och industriell utveckling, 2007
Serie
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1080
Nyckelord
Cast iron, Flake graphite, Compacted graphite, Spheroidal graphite, Elastic deformation, Plastic deformation, Modulus of elasticity, Graphite modulus of elasticity, Strength coefficient, Strain hardening exponent, Acoustic emission
Nationell ämneskategori
Annan materialteknik
Identifikatorer
urn:nbn:se:liu:diva-8776 (URN)978-91-85715-52-7 (ISBN)
Disputation
2007-05-25, sal E1405, Ingenjörshögskolan i Jönköping, Jönköping, 10:00 (Engelska)
Opponent
Handledare
Tillgänglig från: 2007-04-20 Skapad: 2007-04-20 Senast uppdaterad: 2009-03-13
2. The influence of graphite morphology on the elastic behaviour of cast irons
Öppna denna publikation i ny flik eller fönster >>The influence of graphite morphology on the elastic behaviour of cast irons
2005 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The morphology of the graphite phase largely controls the resulting properties of different grades of cast iron. In flake graphite cast irons, the mechanical properties are low while the thermal conductivity is high. In contrast, with spheroidal graphite cast irons, the mechanical properties are high while the thermal conductivity is low. These differences must be accounted for in the design work of diesel engines when choosing the material grade of different components. In this work the influence of graphite morphology on the deformation behaviour of cast irons has been studied with an emphasis on the elastic region.

The studied material grades originated from castings for marine diesel engine piston rings with different chemical analyses. This gave rise to six material grades with different nodularities and three material grades with different carbon equivalents. For these different material grades the mechanical properties were determined and the deformation behaviour was examined by means of mechanical testing and acoustic emission measurements. These data were correlated to microstructural parameters.

When studying the modulus of elasticity it was found that the modulus of elasticity of the inherent graphite phase depends on the roundness of the graphite particles and is due to the different elasticity in the two main crystallographic directions of the graphite lattice. The graphite particles are structured in different ways in flake graphite and spheroidal graphite, which gives rise to different stiffness at loading. The modelling and experiments support the observation that the average modulus of elasticity of the graphite phase depends on the morphology. This improves the understanding of the differences in the modulus of elasticity of the different studied material grades. The correlation between the modulus of elasticity of the graphite phase and the bulk nodularity of the cast iron specimen was found to be linear. This linear function was used when modelling the effective modulus of elasticity of the different cast iron grades with very high accuracy between experimental and theoretical values.

Another factor affecting the elastic response when subjecting a cast iron component to tensile load was found to be the plastic deformation that actually occurs at very low strains for all of the studied cast iron grades. lt was found that the plastic deformation in the low strain, elastic region governs the modulus of elasticity of cast irons. The plastic deformation in the seemingly elastic region was quantified by using acoustic emission measurements. These measurements showed that the amount of plastic deformation in the elastic region was largely controlled by the graphite morphology. It was concluded that, as the roundness of the graphite particles increases, the plastic activity in the elastic region decreases and the energy absorption ability increases.

Förlag
s. 25
Serie
Linköping Studies in Science and Technology. Thesis, ISSN 0280-7971 ; 1140
Nyckelord
Cast iron, flake graphite, compacted graphite, spheroidal graphite, elastic behaviour, modulus of elasticity, graphite modulus of elasticity, nodularity, aspect ratio, plastic deformation, acoustic emission
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
urn:nbn:se:liu:diva-30053 (URN)15513 (Lokalt ID)91-8529-707-0 (ISBN)15513 (Arkivnummer)15513 (OAI)
Tillgänglig från: 2009-10-09 Skapad: 2009-10-09 Senast uppdaterad: 2013-11-28

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextLink to Ph.D. Thesis

Personposter BETA

Sjögren, Torsten

Sök vidare i DiVA

Av författaren/redaktören
Sjögren, Torsten
Av organisationen
KonstruktionsmaterialTekniska högskolan
Teknik och teknologier

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 3505 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf