liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Reduction of Substrate Noise in Mixed-Signal Circuits
Linköpings universitet, Institutionen för systemteknik, Elektroniksystem. Linköpings universitet, Tekniska högskolan.
2007 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

In many consumer products, e.g., cellular phones and handheld computers, both digital and analog circuits are required. Nowadays, it is possible to implement a large subsystem or even a complete system, that earlier required several chips, on a single chip. A system on chip (SoC) has generally the advantages of lower power consumption and a smaller fabrication cost compared with multi-chip solutions. The switching of digital circuits generates noise that is injected into the silicon substrate. This noise is known as substrate noise and is spread through the substrate to other circuits. The substrate noise received in an analog circuit degrades the performance of the circuit. This is a major design issue in mixed-signal ICs where analog and digital circuits share the same substrate.

Two new noise reduction methods are proposed in this thesis work. The first focuses n reducing the switching noise generated in digital clock buffers. The strategy is to use a clock with long rise and fall times in conjunction with a special D flip-flop. It relaxes the constraints on the clock distribution net, which also reduce the design effort. Measurements on a test chip implemented in a 0.35 μm CMOS technology show that the method can be implemented in an IC with low cost in terms of speed and power consumption. A noise reduction up to 50% is obtained by using the method. The measured power consumption of the digital circuit, excluding the clock buffer, increased 14% when the rise and fall times of the clock were increased from 0.5 ns to 10 ns. The corresponding increase in propagation delay was less than 0.5 ns corresponding to an increase of 50% in propagation delay of the registers.

The second noise reduction method focuses on reducing simultaneous switching noise below half the clock frequency. This frequency band is assumed to be the signal band of an analog circuit. The idea is to use circuits that have as close to periodic power supply currents as possible to obtain low simultaneous switching noise below the clock in the frequency domain. For this purpose we use precharged differential cascode switch logic together with a novel D flip-flop. To evaluate the method two pipelined adders have been implemented on transistor level in a 0.13 μm CMOS technology, where the novel circuit is implemented with our method and the reference circuit with static CMOS logic together with a TSPC D flip-flop. According to simulation results, the frequency components in the analog signal band can be attenuated from 10 dB up to 17 dB using the proposed method. The cost is mainly an increase in power consumption of almost a factor of three.

Comparisons between substrate coupling in silicon-on-insulator (SOI) and conventional bulk technology are made using simple models. The objective is to get an understanding of how the substrate coupling differs in SOI from the bulk technology. The results show that the SOI has less substrate coupling if no guard band is used, up to a certain frequency that is dependent of the test case. Introducing a guard band resulted in a higher attenuation of substrate noise in bulk than in SOI.

An on-chip measurement circuit aiming at measuring simultaneous switching noise has been designed in a 0.13 μm SOI CMOS technology. The measuring circuit uses a single comparator per channel where several passes are used to capture the waveform. Measurements on a fabricated testchip indicate that the measuring circuit works as intended.

A small part of this thesis work has been done in the area of digit representation in digital circuits. A new approach to convert a number from two’s complement representation to a minimum signed-digit representation is proposed. Previous algorithms are working either from the LSB to the MSB (right-to-left) or from the MSB to the LSB (left-to-right). The novelty in the proposed algorithm is that the conversion is done from left-to-right and right-to-left concurrently. Using the proposed algorithm, the critical path in a conversion circuit can be nearly halved compared with the previous algorithms. The area and power consumption, of the implementation of the proposed algorithm, are somewhere between the left-to-right and right-to-left implementations.

Ort, förlag, år, upplaga, sidor
Institutionen för systemteknik , 2007.
Serie
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1094
Nyckelord [en]
Mixed-signal, Substrate noise, Substrate modeling, Simultaneous switching noise, SSN, Digital, Analog, Clock
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
URN: urn:nbn:se:liu:diva-8813ISBN: 978-91-85715-12-1 (tryckt)OAI: oai:DiVA.org:liu-8813DiVA, id: diva2:23520
Disputation
2007-05-10, Key1, Key-huset, Campus Valla, Linköpings universitet, Linköping, 13:15 (Engelska)
Opponent
Handledare
Anmärkning
Articles I, II, III, IV, VII and IX are published with permisson from IEEE dated 07/05/18. Copyright IEEE.Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-04-21
Delarbeten
1. A strategy for reducing clock noise in mixed-signal circuits
Öppna denna publikation i ny flik eller fönster >>A strategy for reducing clock noise in mixed-signal circuits
2002 (Engelska)Ingår i: Proc. IEEE 45th Midwest Symp. on Circuits and Systems, MWSCAS'02, 2002, Vol. 1, s. 29-32Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Digital switching noise is of major concern in mixed-signal circuits due to the coupling of the noise via a shared substrate to the analog circuits. A significant noise source in this context is the digital clock network that generally has a high switching activity. There is a large capacitive coupling between the clock network and the substrate. Switching of the clock produces current peaks causing simultaneous switching noise (SSN). Sharp clock edges yields a high frequency content of the clock signal and a large SSN. High frequency noise is less attenuated through the substrate than low frequencies due to the parasitic inductance of the interconnect from on-chip to off-chip. In this work, we present a strategy that targets the problems with clock noise. The approach is to generate a clock with smooth edges, i.e. reducing both the high frequency components of the clock signal and the current peaks produced in the power supply. We use a special digital D flip-flop circuit that operates well with the clock. A test chip has been designed where we can control the rise and fall time of the clock edges in a digital FIR filter, and measure the performance of a fifth-order analog active-RC filter.

Nyckelord
FIR filters, RC circuits, active filters, clocks, flip-flops, integrated circuit noise, mixed analog-digital integrated circuits
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14442 (URN)0-7803-7523-8 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
2. Design of circuits for a robust clocking scheme
Öppna denna publikation i ny flik eller fönster >>Design of circuits for a robust clocking scheme
2004 (Engelska)Ingår i: Proc. 12th Mediterranean Electrotechnical Conf., MELECON'04, 2004, Vol. 1, s. 185-188Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The design of a clock distribution network in a digital integrated circuit is challenging in terms of obtaining low power consumption, low waveform degradation, low clock skew and low simultaneous switching noise. In this work we aim at alleviating these design restrictions by using a clock buffer with reduced size and a D flip-flop circuit with relaxed constraints on the rise and fall times of the clock. According to simulations the energy dissipation of a D flip-flop, implemented in a 0.35 μm process, increases with only 21% when the fall time of the clock is increased from 0.05 ns to 7.0 ns. Considering that smaller clock buffers can be used there is a potential of power savings by using the suggested clocking scheme.

Nyckelord
buffer circuits, circuit noise, circuit simulation, clocks, digital integrated circuits, flip-flops, integrated circuit modelling, low-power electronics
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14443 (URN)10.1109/MELCON.2004.1346804 (DOI)0-7803-8271-4 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-05
3. Evaluation of a clocking strategy with relaxed constraints on clock edges
Öppna denna publikation i ny flik eller fönster >>Evaluation of a clocking strategy with relaxed constraints on clock edges
2004 (Engelska)Ingår i: Proc. TENCON'04, 2004, Vol. 4, s. 411-414Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

A strategy that aims at relaxing the design of the clock network in digital circuits is evaluated through simulations and measurements on a test circuit. In the strategy a clock with long rise and fall times is used in conjunction with a D flip-flop that operates well with this clock. The test circuit consists of a digital FIR filter and a clock buffer with adjustable driving strength. It was designed and manufactured in a 0.35 μm CMOS process. The energy dissipation of the circuit increased 14% when the rise and fall times of the clock increased from 0.5 ns to 10 ns. The corresponding increase in propagation delay was less than 0.5 ns, i.e. an increase of 50% in propagation delay of the register. The results in this paper show that the clocking strategy can be implemented with low costs of power and speed.

Nyckelord
CMOS logic circuits, FIR filters, clocks, delays, flip-flops
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14444 (URN)10.1109/TENCON.2004.1414957 (DOI)0-7803-8560-8 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-05
4. Reduction of simultaneous switching noise in digital circuits
Öppna denna publikation i ny flik eller fönster >>Reduction of simultaneous switching noise in digital circuits
2006 (Engelska)Ingår i: Proc. 24th IEEE Norchip Conf., NORCHIP'06, 2006, s. 187-190Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this paper the authors present results from measurements on a test chip used to evaluate our method for reduction of substrate noise that originates from the clock in digital circuits. The authors use long rise and fall times of the clock signal and a D flip-flop that operates well with this clock. With this approach, smaller clock buffers can be used, which results in smaller current peaks on the power supply lines and therefore less switching noise. The measured substrate noise on the test chip was reduced by 20% and up to 54%. With optimized clock buffers this method has a potential of an even larger noise reduction.

Nyckelord
CMOS integrated circuits, buffer circuits, clocks, flip-flops, integrated circuit noise, integrated circuit testing
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14445 (URN)10.1109/NORCHP.2006.329207 (DOI)1-4244-0772-9 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
5. Effect of simultaneous switching noise on an analog filter
Öppna denna publikation i ny flik eller fönster >>Effect of simultaneous switching noise on an analog filter
2006 (Engelska)Ingår i: Proc. Int. Conf. on Electronics, Circuits and Systems, ICECS'06, 2006, s. 898-901Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this work a digital filter is placed on the same chip as an analog filter. We investigate how the simultaneous switching noise is propagated from the digital filter to different nodes on a manufactured chip. Conventional substrate noise reduction methods are used, e.g., separate power supplies, guard rings, and multiple pins for power supplies. We also investigate if the effect of substrate noise on the analog filter can be reduced by using a noise reduction method, which use long rise and fall times of the digital clock. The measured noise on the output of the analog filter was reduced by 30% up to 50% when the method was used.

Nyckelord
clocks, digital filters, integrated circuit noise, mixed analog-digital integrated circuits
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14446 (URN)10.1109/ICECS.2006.379934 (DOI)1-4244-0395-2 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
6. Introduction to substrate noise in SOI CMOS integrated circuits
Öppna denna publikation i ny flik eller fönster >>Introduction to substrate noise in SOI CMOS integrated circuits
2005 (Engelska)Ingår i: Proc. National Conf. on Radio Science, RVK'05, 2005Konferensbidrag, Publicerat paper (Övrigt vetenskapligt)
Abstract [en]

In this paper an introduction to substrate noise in silicon oninsulator (SOI) is given. Differences between substratenoise coupling in conventional bulk CMOS and SOICMOS are discussed and analyzed by simulations. The efficiencyof common substrate noise reduction methods arealso analyzed. Simulation results show that the advantageof the substrate isolation in SOI is only valid up to a frequencythat highly depends on the chip structure. In bulk,guard bands are normally directly connected to the substrate.In SOI, the guard bands are coupled to the substratevia the parasitic capacitance of the silicon oxide. Therefore,the efficiency of a guard may be much larger in aconventional bulk than in SOI. One opportunity in SOI isthat a much higher resistivity of the substrate can be used,which results in a significantly higher impedance up to afrequency where the coupling is dominated by the capacitivecoupling of the substrate.

Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14447 (URN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
7. Programmable reference generator for on-chip measurement
Öppna denna publikation i ny flik eller fönster >>Programmable reference generator for on-chip measurement
2006 (Engelska)Ingår i: Proc. 24th IEEE Norchip Conf., NORCHIP'06, 2006, s. 89-92Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this work, circuits for on-chip measurement and periodic waveform capture are designed. The aim is to analyze disturbances in mixed-signal chips such as simultaneous switching noise and the transfer of substrate noise. A programmable reference generator that replaces the standard digital-to-analog converter is proposed. It is based on a resistor string that is connected in a circular structure. A feature is that the reference outputs to the different comparators in the measurement channels are distributed over the nodes of the resistor string. Comparing with using a complete digital-to-analog converter, the use of a buffer is avoided. Hence, there is a potential reduction in the parasitic capacitance and power consumption as well as an increase in speed. We present results from a test chip demonstrating that simultaneous switching noise can be measured with the presented approach.

Nyckelord
comparators, digital-analog conversion, electric noise measurement, integrated circuit measurement, integrated circuit noise, programmable circuits, reference circuits
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14448 (URN)10.1109/NORCHP.2006.329251 (DOI)1-4244-0772-9 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
8. Reduction of simultaneous switching noise in analog signal band
Öppna denna publikation i ny flik eller fönster >>Reduction of simultaneous switching noise in analog signal band
2007 (Engelska)Ingår i: Proc. IEEE European Conf. Circuit Theory and Design, ECCTD'07, 2007, s. 148-151Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

In this work we focus on reducing the simultaneous switching noise located in the frequency band from DC up to half of the digital clock frequency. This frequency band is assumed to be the signal band of an analog circuit. The idea is to use circuits that have as periodic power supply currents as possible to obtain low simultaneous switching noise below the clock in the frequency domain. We use precharged differential cascode switch logic together with a novel D flip-flop. To evaluate the method two pipelined adders have been implemented on transistor level in a 0.13 mum CMOS technology, where the novel circuit is implemented with our method and the reference circuit with static CMOS logic together with a TSPC D flip-flop. According to simulation results, the frequency components in the analog signal band can be attenuated from 10 dB up to 17 dB when using the proposed method. The cost is an increase in power consumption of almost a factor of three and a higher transistor count.

Nyckelord
CMOS integrated circuits, adders, flip-flops, frequency-domain analysis, mixed analog-digital integrated circuits, analog signal band, digital clock frequency, frequency components, frequency domain, higher transistor count, pipelined adders, precharged differential cascode switch logic, static CMOS logic, switching noise reduction, transistor level
Nationell ämneskategori
Annan elektroteknik och elektronik
Identifikatorer
urn:nbn:se:liu:diva-14449 (URN)10.1109/ECCTD.2007.4529558 (DOI)978-1-4244-1341-6 (ISBN)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2009-10-14
9. Bidirectional Conversion to Minimum Signed-Digit Representation
Öppna denna publikation i ny flik eller fönster >>Bidirectional Conversion to Minimum Signed-Digit Representation
2006 (Engelska)Ingår i: Circuits and Systems, 2006. ISCAS 2006., 2006Konferensbidrag, Publicerat paper (Övrigt vetenskapligt)
Abstract [en]

In this work an approach to converting a number in two's complement representation to a minimum signed-digit representation is proposed. The novelty in this work is that this conversion is done from left-to-right and right-to-left concurrently. Hence, the execution time is significantly decreased, while the area overhead is small.

Nyckelord
Boolean functions, digital arithmetic, bidirectional conversion, signed-digit representation
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
urn:nbn:se:liu:diva-14450 (URN)10.1109/ISCAS.2006.1693109 (DOI)
Tillgänglig från: 2007-05-22 Skapad: 2007-05-22 Senast uppdaterad: 2015-03-11

Open Access i DiVA

fulltext(1072 kB)5771 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 1072 kBChecksumma MD5
51398d7806e2570d0cf81f9fa713dfc7e13baa9ef691652c419788e93c44cd77efff2711
Typ fulltextMimetyp application/pdf

Personposter BETA

Backenius, Erik

Sök vidare i DiVA

Av författaren/redaktören
Backenius, Erik
Av organisationen
ElektroniksystemTekniska högskolan
Annan elektroteknik och elektronik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 5777 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 3450 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf