liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of Cooling and Shot Peening on Residual Stresses and Fatigue Performance of Milled Inconel 718
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.ORCID-id: 0000-0002-8304-0221
Ytstruktur Arboga AB, Arboga, Sweden.
Visa övriga samt affilieringar
2017 (Engelska)Ingår i: Residual Stresses 2016 ICRS 10 / [ed] T.M. Holden, O. Muránsky, and L. Edwards, 2017, Vol. 2, s. 13-18Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The present study highlights the effect of cooling and post-machining surface treatment of shot peening on the residual stresses and corresponding fatigue life of milled superalloy Inconel 718. It was found that tensile residual stresses were created on the milled surface, regardless of the use of coolant, however, the wet milling operation led to a lower surface tension and a reduced thickness of the tensile layer. The shot peening performed on the dry-milled specimens completely annihilated the surface tensile residual tresses and introduced a high level of surface compression. A comparable fatigue life for the wet-milled specimens was obtained as compared with the specimens prepared by dry milling. This is very likely attributed to that the milling-induced surface damage with respect to cracked non-metallic inclusions is the predominant cause of the fatigue failure. The presence of the compressive layer induced by shot peening resulted in a significant increase of the fatigue life and strength, while the extent to which the lifetime was prolonged was decreased as the applied load was increased.

Ort, förlag, år, upplaga, sidor
2017. Vol. 2, s. 13-18
Serie
Materials Research Proceedings, ISSN 2474-395X
Nyckelord [en]
Residual stresses, surface integrity, milling, shot peening, superalloys, fatigue
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:liu:diva-132001DOI: 10.21741/9781945291173-3ISI: 000401041500003ISBN: 978-1-9452-9116-6 (tryckt)OAI: oai:DiVA.org:liu-132001DiVA, id: diva2:1034910
Konferens
10th International Conference on Residual Stresses ICRS-10, Sydney, Australia, 3-8 July 2016
Anmärkning

Funding agencies: Linkoping University [2009-00971]; Ytstruktur Arboga AB; Siemens Industrial Turbomachinery AB

Tillgänglig från: 2016-10-13 Skapad: 2016-10-13 Senast uppdaterad: 2017-06-13Bibliografiskt granskad
Ingår i avhandling
1. Surface Integrity and Fatigue Performance of Nickel-based Superalloys
Öppna denna publikation i ny flik eller fönster >>Surface Integrity and Fatigue Performance of Nickel-based Superalloys
2017 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Due to global warming, the demand for more efficient gas turbines has increased. A way to achieve this, is by increasing the operating temperature of the gas turbine. Therefore, nickel-based superalloys have been developed to withstand these extreme temperatures and loads, especially in the hot sections. Today, the way of operating land-based gas turbines is changing. Instead of running for long periods of time, the operation is becoming more flexible, with ever-increasing cyclic loads and number of start and stop cycles. To handle the increased stress and cycles, component resistance to fatigue failures need to be improved.

Surface integrity is critical to fatigue performance, since fatigue cracks normally initiate at a surface. Machining changes the surface integrity which can result in worse fatigue resistance. The work presented in this Ph.D. thesis was conducted in collaboration with Siemens Industrial Turbomachinery AB in Finspång, Sweden. Surface integrity changes which are induced during machining and their effects on fatigue performance have been studied on the alloy Inconel 718. Inconel 718 is a widely-used nickel-based superalloy for high temperature applications in modern gas turbines.

Broaching, milling, and wire electrical discharge machining, related to component manufacturing in turbo machinery industries, were included in this study. Machining induced surface defects provide preferential sites for fatigue crack initiation which influence the fatigue performance of the alloy. If compressive residual stresses are induced during machining, they benefit the fatigue life by retarding fatigue crack initiation away from surface regions. Shot peening was performed on machined Inconel 718, by which high compressive residual stresses are deliberately induced. It results in enhanced fatigue performance.

The high temperatures in gas turbines generally deteriorate the surface integrity. Recrystallization often occurs in the highly deformed surface layer. Microstructural degradation, in the form of α-Cr precipitates, have also been frequently observed in the deformed surface and sub-surface microstructure. Oxidation at elevated temperatures degrades the surface integrity and thereby also the fatigue performance. Fatigue cracks are preferably initiated at oxidized surface carbides, if thermal exposure has been made prior to the test. It is even worse when high temperatures relax the beneficial surface compression induced by shot-peening and thereby lowering the fatigue resistance.

Machinability of a newly developed nickel-based superalloy, AD 730TM, and the surface integrity induced during turning have also been studied in this thesis project. AD 730TM is a candidate for turbine disc applications with an operating temperature above 650 °C. At such high temperatures, Inconel 718 is no longer stable and its mechanical properties start to degrade.

To summarize, the results from this thesis work show the importance of understanding surface integrity effects for fatigue applications, especially in harsh environments. Moreover, the knowledge gained through this work could be used for surface enhancement of turbine components which are subjected to a high risk of fatigue failure. These will contribute to more efficient and flexible power generation by gas turbines.

Ort, förlag, år, upplaga, sidor
Linköping: Linköping University Electronic Press, 2017. s. 72
Serie
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1821
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik Annan materialteknik Tribologi (ytteknik omfattande friktion, nötning och smörjning) Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:liu:diva-134124 (URN)10.3384/diss.diva-134124 (DOI)9789176856000 (ISBN)
Disputation
2017-02-17, ACAS,Hus A, Campus Valla, Linköping, 10:15 (Engelska)
Opponent
Handledare
Tillgänglig från: 2017-01-24 Skapad: 2017-01-24 Senast uppdaterad: 2019-10-11Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Chen, ZhePeng, RuMoverare, JohanJohansson, Sten
Av organisationen
KonstruktionsmaterialTekniska fakulteten
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
isbn
urn-nbn

Altmetricpoäng

doi
isbn
urn-nbn
Totalt: 547 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf