liu.seSearch for publications in DiVA
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Topology Optimization for Additive Manufacturing Considering Stress and Anisotropy
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Mekanik och hållfasthetslära.
2017 (engelsk)Independent thesis Advanced level (degree of Master (Two Years)), 20 poäng / 30 hpOppgave
Abstract [en]

Additive manufacturing (AM) is a particularly useful manufacturing method for components designed using topology optimization (TO) since it allows for a greater part complexity than any traditional manufacturing method. However, the AM process potentially leads to anisotropic material properties due to the layer-by-layer buildup of parts and the fast and directional cooling. For Ti6Al4V tensile specimens built using electron beam melting (EBM), it has been observed that flat built specimens show superior strength and elastic moduli compared to top built specimens. Designs with the loading direction parallel to the build layers are therefore expected to show greater reliability.

In this thesis a procedure is developed to optimize the AM build orientation considering anisotropic elastic material properties. A transversely isotropic material model is used to represent the in-plane and out-of-plane characteristics of AM produced parts. Two additional design variables are added to the TO formulation in order to control the orientation of the material using a coordinate transformation. Sensitivity analysis for the material direction variables is conducted for compliance as well as maximum von-Mises stress using a -norm stress aggregation function.

The procedures for the AM build orientation optimization and stress constraints are implemented in the finite element software TRINITAS and evaluated using a number of examples in 2D and 3D. It is found that the procedure works well for compliance as well as stress but that a combination of these may lead to convergence issues due to contradicting optimal material orientations. An evaluation of the -norm stress aggregation function showed that a single global stress measure in combination with a stress correction procedure works well for most problems given that the mesh is refined enough to resolve the stresses accurately.  

sted, utgiver, år, opplag, sider
2017. , s. 68
Emneord [en]
Topology Optimization, Stress Constraints, Additive Manufacturing, Anisotropic Material Proporties
HSV kategori
Identifikatorer
URN: urn:nbn:se:liu:diva-141609ISRN: LIU-IEI-TEK-A--17/02790—SEOAI: oai:DiVA.org:liu-141609DiVA, id: diva2:1146435
Fag / kurs
Mechanical Engineering
Presentation
2017-06-01, 315:934, 581 83 Linköping, Linköping, 08:43 (engelsk)
Veileder
Examiner
Tilgjengelig fra: 2017-10-09 Laget: 2017-10-03 Sist oppdatert: 2017-10-31bibliografisk kontrollert

Open Access i DiVA

Topology Optimization for Additive Manufacturing Considering Stress and Anisotropy(4728 kB)332 nedlastinger
Filinformasjon
Fil FULLTEXT02.pdfFilstørrelse 4728 kBChecksum SHA-512
66db7b7ba490a3b06ca6765362d938084bdc3c13a76219ed8e0719b11bed8b79366d9033a6031ec8af6f57dceb3084c8a67887f696e87bcb9340f9d13be9a076
Type fulltextMimetype application/pdf

Søk i DiVA

Av forfatter/redaktør
Alm Grundström, Henrik
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 366 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 3442 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf