liu.seSearch for publications in DiVA
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Plastic Deformation and Residual Stress in High Speed Turning of AD730™ Nickel-based Superalloy with PCBN and WC Tools
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Division of Production and Materials Engineering,Lunds University, Sweden.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Seco Tools AB, Fagersta, Sweden.
Vise andre og tillknytning
2018 (engelsk)Inngår i: Procedia CIRP 71 (2018) pp 440-445, Elsevier, 2018, Vol. 71, s. 440-445Konferansepaper, Publicerat paper (Fagfellevurdert)
Abstract [en]

A higher gas turbine efficiency can be achieved by increasing the operating temperature in hot sections. AD730™ is a recently-developed wrought/cast nickel-based superalloy which can maintain excellent mechanical properties above 700 ℃. However, machining of AD730™ could be a difficult task like other nickel-based superalloys. Therefore, studies are needed with respect to the machinability of this new alloy.

In this paper, high-speed turning was performed on AD730™ using polycrystalline cubic boron nitride (PCBN) tools and coated tungsten carbide (WC) tools at varied cutting speeds. The surface integrity was assessed in two important aspects, i.e., surface and sub-surface plastic deformation and residual stresses. The PCBN tools generally showed better performance compared with the WC tools since it led to reduced machining time without largely compromising the surface integrity achieved. The optimal cutting speed was identified in the range of 200-250 m/min when using the PCBN tools, which gives rise to a good combination of machining efficiency and surface integrity. The further increase of the cutting speed to 300 m/min resulted in severe and deep plastic deformation. Meanwhile, a continuous white layer was formed at the machined surface. When turning with the WC tools, the increased cutting speed from 80 m/min to 100 m/min showed very little effect with respect to the plastic deformation on the machined surface. It was found that tensile residual stresses were developed on all machined surfaces no matter when the PCBN or WC tools were used, and the surface tension was generally increased with increasing cutting speed. The tensile layer might need to be modified by e.g., post-machining surface treatments such as shot peening, if taking good fatigue performance into consideration.

sted, utgiver, år, opplag, sider
Elsevier, 2018. Vol. 71, s. 440-445
Emneord [en]
plastic deformation, residual stress, nickel-based superalloy, AD730TM, high-speed turning
HSV kategori
Identifikatorer
URN: urn:nbn:se:liu:diva-148484DOI: 10.1016/j.procir.2018.05.051OAI: oai:DiVA.org:liu-148484DiVA, id: diva2:1216679
Konferanse
The 4th CIRP Conference on Surface Integrity, 11th-13th July, Tianjin, China
Tilgjengelig fra: 2018-06-12 Laget: 2018-06-12 Sist oppdatert: 2018-07-03

Open Access i DiVA

fulltext(1193 kB)184 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 1193 kBChecksum SHA-512
dcd8d33df12077a7456954ed8e5d802e5c041e904c8c21b24da11b406938a8f40d1fda02dbba2c4084493a2f12c3dd95f02a32a11c0b17492b0a83fed2d40d56
Type fulltextMimetype application/pdf

Andre lenker

Forlagets fulltekst

Personposter BETA

Chen, ZhePeng, Ru LinGustafsson, DavidPalmert, FransMoverare, Johan

Søk i DiVA

Av forfatter/redaktør
Chen, ZhePeng, Ru LinGustafsson, DavidPalmert, FransMoverare, Johan
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 184 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 131 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf