liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of Machining Parameters on Cutting Force and Surface Integrity when High-Speed Turning AD730™ with PCBN Tools
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Division of Production and Materials Engineering, Lund University, Lund, Sweden.
Seco Tools AB, Fagersta, Sweden.
Visa övriga samt affilieringar
2019 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 100, nr 9-12, s. 2601-2615Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The novel wrought nickel-based superalloy, AD 730™, is a good candidate material for turbine disc applications at high temperatures beyond 650 °C. The present study focuses on the machining performance of this newly developed alloy under high-speed turning conditions with advanced PCBN tools. Meanwhile, the machined surface integrity as influenced by cutting speed and feed rate was also investigated. The surface integrity was thoroughly characterized in terms of surface roughness and morphology, machining-induced plastic deformation, white layer formation, and residual stresses. It has been found that the cutting speed and feed rate had a strong effect on the cutting forces and resultant surface integrity. The cutting forces required when machining the alloy were gradually reduced with increasing cutting speed, while at 250 m/min and above, the flank tool wear became stronger which led to increased thrust force and feed force. A higher feed rate, on the other hand, always resulted in higher cutting forces. Increasing the cutting speed and feed rate in general deteriorated the surface integrity. High cutting speeds within the range of 200–250 m/min and a low feed rate of 0.1 mm/rev are preferable in order to implement more cost-effective machining without largely reducing the surface quality achieved. The formation of tensile residual stresses on the machined AD 730™, however, could be of a concern where good fatigue resistance is critical.

Ort, förlag, år, upplaga, sidor
Springer London, 2019. Vol. 100, nr 9-12, s. 2601-2615
Nyckelord [en]
Nickel-based superalloy, High-speed turning, Cutting forces, Surface integrity, AD730, Cubic boron nitride (CBN) tool
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:liu:diva-153292DOI: 10.1007/s00170-018-2792-1ISI: 000458310400032Scopus ID: 2-s2.0-85055531180OAI: oai:DiVA.org:liu-153292DiVA, id: diva2:1269391
Tillgänglig från: 2018-12-10 Skapad: 2018-12-10 Senast uppdaterad: 2019-03-05Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Chen, ZhePeng, Ru LinMoverare, Johan

Sök vidare i DiVA

Av författaren/redaktören
Chen, ZhePeng, Ru LinMoverare, Johan
Av organisationen
KonstruktionsmaterialTekniska fakulteten
I samma tidskrift
The International Journal of Advanced Manufacturing Technology
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 53 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf