liu.seSearch for publications in DiVA
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Thermomechanical fatigue crack growth in a single crystal nickel base superalloy
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.ORCID-id: 0000-0002-8304-0221
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Mekanik och hållfasthetslära. Linköpings universitet, Tekniska fakulteten.
2019 (engelsk)Inngår i: International Journal of Fatigue, ISSN 0142-1123, E-ISSN 1879-3452, Vol. 122, s. 184-198Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Thermomechanical fatigue crack growth in a single crystal nickel base superalloy was studied. Tests were performed on single edge notched specimens, using in phase and out of phase thermomechanical fatigue cycling with temperature ranges of 100-750°C and 100-850°C and hold times at maximum temperature ranging from 10s to 6h. Isothermal testing at 100°C, 750°C and 850°C was also performed using the same test setup. A compliance-based method is proposed to experimentally evaluate the crack opening stress and thereby estimate the effective stress intensity factor range ΔKeff for both isothermal and nonisothermal conditions. For in phase thermomechanical fatigue, the crack growth rate is increased if a hold time is applied at the maximum temperature. By using the compliance-based crack opening evaluation, this increase in crack growth rate was explained by an increase in the effective stress intensity factor range which accelerated the cycle dependent crack growth. No significant difference in crack growth rate vs ΔKeff was observed between in phase thermomechanical fatigue tests and isothermal tests at the maximum temperature. For out of phase thermomechanical fatigue, the crack growth rate was insensitive to the maximum temperature and also to the length of hold time at maximum temperature. The crack growth rate vs ΔKeff during out of phase thermomechanical fatigue was significantly higher than during isothermal fatigue at the minimum temperature, even though the advancement of the crack presumably occurs at the same temperature. Dissolution of γ′ precipitates and recrystallization at the crack tip during out of phase thermomechanical fatigue is suggested as a likely explanation for this difference in crack growth rate.

sted, utgiver, år, opplag, sider
Elsevier, 2019. Vol. 122, s. 184-198
Emneord [en]
single crystal superalloy, thermomechanical fatigue, crack growth, crack closure
HSV kategori
Identifikatorer
URN: urn:nbn:se:liu:diva-154074DOI: 10.1016/j.ijfatigue.2019.01.014ISI: 000462110100017OAI: oai:DiVA.org:liu-154074DiVA, id: diva2:1283009
Merknad

Funding agencies: Siemens Industrial Turbomachinery AB in Finspang, Sweden; Swedish Energy Agency, via the Research Consortium of Materials Technology for Thermal Energy Processes [KME-702]

Tilgjengelig fra: 2019-01-28 Laget: 2019-01-28 Sist oppdatert: 2019-04-08
Inngår i avhandling
1. Crack growth in single crystal nickel base superalloys under isothermal and thermomechanical fatigue
Åpne denne publikasjonen i ny fane eller vindu >>Crack growth in single crystal nickel base superalloys under isothermal and thermomechanical fatigue
2019 (engelsk)Licentiatavhandling, med artikler (Annet vitenskapelig)
Abstract [en]

This work concerns the fatigue crack growth behaviour of nickel base single crystal superalloys. The main industrial application of this class of materials is in gas turbine blades, where the ability to withstand severe mechanical loading in combination with high temperatures is required. In order to ensure the structural integrity of gas turbine blades, knowledge of the fatigue crack growth behaviour under service-like conditions is of utmost importance. The aim of the present work is both to improve the understanding of the crack growth behaviour of single crystal superalloys and also to improve the testing and evaluation methodology for crack propagation under thermomechanical fatigue loading conditions. Single crystal superalloys have anisotropic mechanical properties and are prone to localization of inelastic deformation along the close-packed planes of the crystal lattice. Under some conditions, crystallographic crack growth occurs along these planes and this is a complicating factor throughout the whole chain of crack propagation life simulation; from material data generation to component calculation. Fatigue crack growth testing has been performed, both using conventional isothermal testing methods and also using thermomechanical fatigue crack growth testing. Experimental observations regarding crystallographic crack growth have been made and its dependence on crystal orientation and testing temperature has been investigated. Quantitative crack growth data are however only presented for the case of Mode I crack growth under isothermal as well as thermomechanical fatigue conditions. Microstructural investigations have been undertaken to investigate the deformation mechanisms governing the crack growth behaviour. A compliance based method for the evaluation of crack opening force under thermomechanical fatigue conditions was developed, in order to enable a detailed analysis of the test data. The crack opening force evaluation proved to be of key importance in the understanding of the crack driving force under different testing conditions.

sted, utgiver, år, opplag, sider
Linköping: Linköping University Electronic Press, 2019. s. 44
Serie
Linköping Studies in Science and Technology. Licentiate Thesis, ISSN 0280-7971 ; 1829
HSV kategori
Identifikatorer
urn:nbn:se:liu:diva-153619 (URN)10.3384/lic.diva-153619 (DOI)9789176851500 (ISBN)
Presentation
2019-01-25, ACAS, A-huset, Campus Valla, Linköpings universitet, Linköping, 09:19 (svensk)
Opponent
Veileder
Merknad

In the printed version of the thesis the series name Linköping Studies in Science and Technology Licentiate of engineering thesis is incorrect. The correct series name is Linköping Studies in Science and Technology Licentiate thesis.

Tilgjengelig fra: 2019-01-04 Laget: 2019-01-04 Sist oppdatert: 2019-01-28bibliografisk kontrollert

Open Access i DiVA

Fulltekst tilgjengelig fra 2021-01-25 17:11
Tilgjengelig fra 2021-01-25 17:11

Andre lenker

Forlagets fulltekst

Personposter BETA

Palmert, FransMoverare, JohanGustafsson, David

Søk i DiVA

Av forfatter/redaktør
Palmert, FransMoverare, JohanGustafsson, David
Av organisasjonen
I samme tidsskrift
International Journal of Fatigue

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 67 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf