liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructural influence on fatigue crack propagation during high cycle fatigue testing of additively manufactured Alloy 718
Univ West, Sweden.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten. Univ West, Sweden.ORCID-id: 0000-0002-8304-0221
Univ West, Sweden.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Konstruktionsmaterial. Linköpings universitet, Tekniska fakulteten.
Visa övriga samt affilieringar
2019 (Engelska)Ingår i: Materials Characterization, ISSN 1044-5803, E-ISSN 1873-4189, Vol. 149, s. 82-94Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

A study of the microstructure of additively manufactured Alloy 718 was performed in order to better understand the parameters that have an influence on the fatigue properties of the material. The specimens were manufactured using two powder bed fusion techniques - Electron Beam Melting (EBM) and Selective Laser Melting (SLM). Four point bending fatigue tests were performed at room temperature with a stress ratio of R = 0.1 and 20 Hz frequency, on material that was either in hot isostatically pressed (HIP) and solution treated and aged (STA) condition or in STA condition without a prior HIP treatment. The grains in the SLM material in the HIP + STA condition have grown considerably both in the hatch and the contour regions; EBM material, in contrast, shows grain growth only in the contour region. Fractographic analysis of the specimens in HIP + STA condition showed a faceted appearance while the specimens in STA condition showed a more planar crack appearance. The crack propagation occurred in a transgranular mode and it was found that precipitates such as NbC, TiN or 8-phase, when present, did not affect the crack path. The areas with larger grains corresponded to the faceted appearance of the fracture surface. This could be attributed to the plastic zone ahead of the crack tip being confined within one grain, in case of the larger grains, which promotes single shear crack growth mode.

Ort, förlag, år, upplaga, sidor
ELSEVIER SCIENCE INC , 2019. Vol. 149, s. 82-94
Nyckelord [en]
Electron beam melting; Selective laser melting; Alloy 718; Fatigue crack propagation; Microstructure; Hot isostatic pressing
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:liu:diva-159293DOI: 10.1016/j.matchar.2019.01.018ISI: 000475837800008OAI: oai:DiVA.org:liu-159293DiVA, id: diva2:1341113
Anmärkning

Funding Agencies|KK Foundation [20160281]

Tillgänglig från: 2019-08-07 Skapad: 2019-08-07 Senast uppdaterad: 2019-08-07

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Sök vidare i DiVA

Av författaren/redaktören
Moverare, JohanDeng, Dunyong
Av organisationen
KonstruktionsmaterialTekniska fakulteten
I samma tidskrift
Materials Characterization
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 59 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf