liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Study on Individual Pressure Control in Energy Efficient Cylinder Drives
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Fluid och mekanisk systemteknik. Linköpings universitet, Tekniska högskolan.ORCID-id: 0000-0002-6371-1390
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling. Linköpings universitet, Tekniska högskolan.
Linköpings universitet, Institutionen för ekonomisk och industriell utveckling, Fluid och mekanisk systemteknik. Linköpings universitet, Tekniska högskolan.
2006 (Engelska)Ingår i: 4th FPNI-Ph.D. Symphosium, FPNI’06, Sarasota, United States, 13th–17th June, 2006, M. Ivantysynova (ed.), 2006, s. 77-99Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

This paper deals with energy efficient mobile valves with cylinder loads. In recent years, the need for energy efficient fluid power systems has increased. The reason is the increasing price of oil as well as tougher environmental regulations. One way of achieving an energy efficient directional valve is to use individually controlled meter-in and meter-out orifices and transfer functionality from hardware to the software controller. This type of solution makes it possible to keep metering losses low. Energy recovery is also made possible since both speed and lowest cylinder chamber pressure can be controlled. The challenge in such a controller is to decouple the chamber pressures in the MIMO (multi-input-multi-output) hydraulic system into independent SISO (single-input-single-output) systems. In this paper, a decoupling based on a linear analysis of the physical system has been implemented and tested in a cylinder position control application. The controller is evaluated in terms of performance and robustness. In the near future, this project will continue with other approaches as well, as there are several interesting control approaches available.

 

Ort, förlag, år, upplaga, sidor
2006. s. 77-99
Nyckelord [en]
Fluid power, separate metering, decouped control
Nationell ämneskategori
Systemvetenskap, informationssystem och informatik
Identifikatorer
URN: urn:nbn:se:liu:diva-12537ISBN: 1-42430-499-7 (tryckt)OAI: oai:DiVA.org:liu-12537DiVA, id: diva2:439
Anmärkning
Volume 1, No. 4Tillgänglig från: 2008-09-12 Skapad: 2008-09-12 Senast uppdaterad: 2018-01-12
Ingår i avhandling
1. Control Strategy for Energy Efficient Fluid Power Actuators: Utilizing Individual Metering
Öppna denna publikation i ny flik eller fönster >>Control Strategy for Energy Efficient Fluid Power Actuators: Utilizing Individual Metering
2007 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

This thesis presents a solution enabling lower losses in hydraulic actuator systems. A mobile fluid power system often contains several different actuators supplied with a single load sensing pump. One of the main advantages is the need of only one system pump. This makes the fluid power system compact and cost-effective.

A hydraulic load often consists of two ports, e.g. motors and cylinders. Such loads have traditionally been controlled by a valve that controls these ports by one single control signal, namely the position of the spool in a control valve. In this kind of valve, the inlet (meter-in) and outlet (meter-out) orifices are mechanically connected. The mechanical connection makes the system robust and easy to control, at the same time as the system lacks flexibility. Some of the main drawbacks are

The fixed relation between the inlet and outlet orifices in most applications produce too much throttling at the outlet orifice under most operating conditions. This makes the system inefficient.

The flow directions are fixed for a given spool position; therefore, no energy recuperation and/or regeneration ability is available.

In this thesis a novel system idea enabling, for example, recuperation and regeneration is presented. Recuperation is when flow is taken from a tank, pressurized by external loads, and then fed back into the pump line. Regeneration is when either cylinder chambers (or motor ports) are connected to the pump line. Only one system pump is needed. Pressure compensated (load independent), bidirectional, poppet valves are proposed and utilized.

The novel system presented in this thesis needs only a position sensor on each compensator spool. This simple sensor is also suitable for identification of mode switches, e.g. between normal, differential and regenerative modes. Patent pending.

The balance of where to put the functionality (hardware and/or software) makes it possible to manoeuvre the system with maintained speed control in the case of sensor failure. The main reason is that the novel system does not need pressure transducers for flow determination. Some features of the novel system:

Mode switches The mode switches are accomplished without knowledge about the pressures in the system

Throttle losses With the new system approach, choice of control and measure signals, the throttle losses at the control valves are reduced

Smooth mode switches The system will switch to regenerative mode automatically in a smooth manner when possible

Use energy stored in the loads The load, e.g. a cylinder, is able to be used as a motor when possible, enabling the system to recuperate overrun loads

The system and its components are described together with the control algorithms that enable energy efficient operation. Measurements from a real application are also presented in the thesis.

Ort, förlag, år, upplaga, sidor
Linköping: Linköping University Electronic Press, 2007. s. 60
Serie
Linköping Studies in Science and Technology. Thesis, ISSN 0280-7971 ; 1341
Nyckelord
Fluid power, mode switch, energy efficient, independent metering, split spool, poppet
Nationell ämneskategori
Strömningsmekanik och akustik
Identifikatorer
urn:nbn:se:liu:diva-12540 (URN)LIU-TEK-LIC-2007:50 (Lokalt ID)978-91-85895-06-9 (ISBN)LIU-TEK-LIC-2007:50 (Arkivnummer)LIU-TEK-LIC-2007:50 (OAI)
Presentation
2007-12-20, A35, Hus A, Campus Valla, Linköpings universitet, Linköping, 10:15 (Engelska)
Opponent
Handledare
Tillgänglig från: 2008-09-12 Skapad: 2008-09-12 Senast uppdaterad: 2020-04-01Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Link to Licentiate thesis

Personposter BETA

Eriksson, BjörnLarsson, JonasPalmberg, Jan-Ove

Sök vidare i DiVA

Av författaren/redaktören
Eriksson, BjörnLarsson, JonasPalmberg, Jan-Ove
Av organisationen
Fluid och mekanisk systemteknikTekniska högskolanInstitutionen för ekonomisk och industriell utveckling
Systemvetenskap, informationssystem och informatik

Sök vidare utanför DiVA

GoogleGoogle Scholar

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 2156 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf