liu.seSök publikationer i DiVA
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Characterization of Surface Modified Hollow Fiber Polyethersulfone Membranes Prepared at Different Air Gaps
Department of Chemical Engineering, IMRI, University of Ottawa, Ottawa, Ontario, Canada.
Department of Chemical Engineering, IMRI, University of Ottawa, Ottawa, Ontario, Canada.
Department of Chemical Engineering, IMRI, University of Ottawa, Ottawa, Ontario, Canada.
Department of Civil Engineering, University of Ottawa, Ottawa, Ontario, Canada.
Visa övriga samt affilieringar
2006 (Engelska)Ingår i: Journal of Applied Polymer Science, ISSN 0021-8995, E-ISSN 1097-4628, Vol. 104, nr 2, s. 710-721Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Hollow fibers were spun from a solution of surface-modifying macromolecule blended polyethersulfone in dimethyl acetamide by using dry-wet spinning method at different air gaps and at room temperature. The air gap was varied from 10 to 90 cm. The ultrafiltration performance of hollow fibers was studied by using aqueous solutions of polyethylene glycols and polyethylene oxides of different molecular weights. Significant difference in surface morphology between the inner and outer surface of the hollow fibers was observed by atomic force microscopy (AFM). Similar results were obtained by contact angle measurement and XPS. Mean pore sizes of the inner surface and outer surface were calculated from AFM images and compared with the pore sizes obtained from mass transport data. Pore size distribution curves were drawn from both data, i.e., from AFM images and mass-transport data, both methods gave similar results.Roughness parameters of the inner and outer surfaces and the sizes of nodular aggregates on both surfaces were measured. An attempt was made to correlate the above parameters with the performance of the membranes. Unexpected values of contact angles of both inner surface and outer surface were obtained. It was observed that the studied membranes could be put into two groups: (i) the membranesfabricated between 10 and 50 cm air gap and (ii) fabricated at higher than 50 cm air gap. A plausible mechanism for the unexpected results was discussed.

Ort, förlag, år, upplaga, sidor
John Wiley & Sons, 2006. Vol. 104, nr 2, s. 710-721
Nyckelord [en]
Hollow fiber; surface-modifying macromolecules; contact angle; AFM; hydrophobicity
Nationell ämneskategori
Kemiteknik Teknik och teknologier
Identifikatorer
URN: urn:nbn:se:liu:diva-101486DOI: 10.1002/app.24853OAI: oai:DiVA.org:liu-101486DiVA, id: diva2:666378
Tillgänglig från: 2013-11-22 Skapad: 2013-11-22 Senast uppdaterad: 2017-12-06Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Person

Rafat, Mehrdad

Sök vidare i DiVA

Av författaren/redaktören
Rafat, Mehrdad
I samma tidskrift
Journal of Applied Polymer Science
KemiteknikTeknik och teknologier

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 249 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf