Full-scale measurements were carried out for investigation of thermal comfort in an office room for a new supply air diffuser. Results of the measurements were performed with both wholefield measuring and traditional point measuring techniques. Experimental results were carried out for supply Archimedes numbers varying from 0.03 to 0.16 and two cooling loads, i.e. 55 and 70 W/m2. Characteristics of indoor environment and occupants’ comfort were explored and analyzed. It was concluded that the airflow pattern and thermal comfort from the investigated low-velocity diffuser were in good agreement with standard ISO 7730.

The flow behavior of isothermal and non-isothermal wall confluent jets (WCJ) ventilation system was investigated experimentally in a mock-up office environment. Two flow regions were identified: first, a primary region is developed below the supply device, with axis along the inlet wall, and a secondary wall-jet forms along the floor. The velocity and temperature fields were recorded by traversing a hot wire and thermistor anemometers for both primary and secondary regions. The results show self-similarity characteristic of the velocity and temperature profiles for both isothermal and non-isothermal WCJ. Maximum velocity decay and its spreading rate are linear and independent of the inlet airflow rate. Minimum temperature difference and its spread also show linear decay. The spreading rates for maximum velocity are similar in both the primary and secondary regions normal to the inlet wall and floor, respectively, which is consistent with previous studies on wall jets. The variation of draught rating is evaluated via mean velocity, turbulence intensity and temperature. Although the WCJ has slow velocity decay, which enables it to cover almost the entire floor of the test room, the draught is acceptable in the occupied zone according to ISO 7730. PMV (predicted mean vote) and PPD (predicted percentage dissatisfied) are presented for the occupied zone of the room.

This study presents numerical investigation of an air supply device based on wall confluent jets in a ventilated room. Confluent jets can be described as multiple round jets issuing from supply device apertures. The jets converge, merge, and combine at a certain distance downstream from the supply device and behave as a united jet, or so-called confluent jet. The numerical predictions of the velocity flow field of isothermal confluent jets with three Reynolds-averaged Navier-Stokes turbulence models (renormalization group k-epsilon, realizable k-epsilon, and shear stress transport k-omega) are reported in the present study. The results of the numerical predictions are verified with detailed experimental measurements by a hot wire anemometer and constant temperature anemometers for two airflow rates. The box method is used to provide the inlet boundary conditions. The study of the airflow distribution shows that a primary wall jet (wall confluent jet) exists close to the supply device along the wetted wall, and a secondary wall jet is created after the stagnation region along the floor. It is presented that the flow field of the primary and secondary wall jet predicted by turbulence models is in good agreement with the experimental data. The current study is also compared with the literature in terms of velocity decay and the spreading rate of the primary and secondary wall jet, the results of which are consistent with each other. Velocity decay and the spreading rate of the secondary wall jet in vertical and lateral directions were studied for different inlet airflow rates and inlet discharge heights. The comparative results demonstrate that the flow behavior is nearly independent of the inlet flow rate. Inlet discharge height is found to have impact close to the inlet, where the velocity decays faster when the jet discharges at higher level. The decay tendency is similar as the jet enters into the room for all discharge heights.

Numerical predictions of the flow field generated by an air supply device based on wall confluent jets are investigated. The numerical predictions of three turbulence models (RNG 𝑘 − 𝜀, Re 𝑘 − 𝜀, and SST 𝑘 − 𝜔) are compared by velocity and temperature measurements. Ventilation performance in terms of thermal comfort and ventilation efficiency is numerically investigated by systematically varying the design of the air supply (nozzle array configuration, nozzle diameter, number of nozzles, and inlet discharge height). The numerical predictions accomplished by the SST 𝑘 − 𝜔 model provide the best agreement with the experimental results. The numerical predictions for supply devices of varying design configuration show that different device designs provide acceptable thermal environments and efficient heat removal. The nozzle diameter and number of nozzles play important roles in determining the airflow pattern, temperature field, and draught distribution. Increased temperature stratification and less draught distribution are achieved by increasing the nozzle diameter and number of nozzles. The spreading rates of the wall jet along the vertical direction for the cases studied are in close agreement with each other and independent of the studied parameters. The flow behavior is rarely independent of the inlet discharge height and configuration of the nozzle array for the studied range.

Abstract The aim of this study was to compare ventilation performance of four different air supply devices in an office environment with respect to thermal comfort, ventilation efficiency and energy-saving potential, by performing numerical simulations. The devices have the acronyms: Mixing supply device (MSD), Wall confluent jets supply device (WCJSD), Impinging jet supply device (IJSD) and Displacement supply device (DSD). Comparisons were made under identical set-up conditions, as well as at the same occupied zone temperature of about 24.2 °C achieved by adding different heat loads and using different air-flow rates. Energy-saving potential was addressed based on the air-flow rate and the related fan power required for obtaining a similar occupied zone temperature for each device. Results showed that the WCJSD and IJSD could provide an acceptable thermal environment while removing excess heat more efficiently than the MSD, as it combined the positive effects of both mixing and stratification principles. This benefit also meant that this devices required less fan power than the MSD for obtaining equivalent occupant zone temperature. The DSD showed a superior performance on heat removal, air exchange efficiency and energy saving to all other devices, but it had difficulties in providing acceptable vertical temperature gradient between the ankle and neck levels for a standing person.

The results of this investigation revealed the airflow distribution from a new design of supply diffuser under non-isothermal conditions. To illustrate the indoor climate parameters in the occupied zone, for both the heating and cooling seasons, an experimental investigation was carried out in industrial premises. The indoor climate was explored at ankle, waist and neck levels for a standing person at different positions, to determine the variation of the thermal comfort indexes and draught rating (DR) with position in the facility. The observed PPD and DR values indicate acceptable levels of thermal comfort in the facility for both summer and winter cases. The conclusion can be drawn that well-distributed airflow saves energy by removing the need for an additional heating and cooling systems during cold and hot weather seasons.