liu.seSearch for publications in DiVA
Change search
ReferencesLink to record
Permanent link

Direct link
Design and Analysis of Diagnosis Systems Using Structural Methods
Linköping University, Department of Electrical Engineering, Vehicular Systems. Linköping University, The Institute of Technology.
2006 (English)Doctoral thesis, monograph (Other academic)
Abstract [en]

In complex and automated technological processes the effects of a fault can quickly propagate and lead to degradation of process performance or even worse to a catastrophic failure. This means that faults have to be found as quickly as possible and decisions have to be made to stop the propagation of their effects and to minimize process performance degradation. The behavior of the process is affected in different ways by different faults and the fault can be found by ruling out faults for which the expected behavior of the process is not consistent with the observed behavior. In model-based diagnosis, a model describes the expected behavior of the process for the different faults.

A device for finding faults is called a diagnosis system. In the diagnosis systems considered here, a number of tests check the consistency of different parts of the model, by using observations of the process. To be able to identify which fault that has occurred, the set of tests that is used must be carefully selected. Furthermore, to reduce the on-line computational cost of running the diagnosis system and to minimize the in general difficult and time-consuming work of tests construction, it is also desirable to use few tests.

A two step design procedure for construction of a diagnosis systems is proposed and it provides the means for selecting which tests to use implicitly by selecting which parts of the model that should be tested with each test. Then, the test design for each part can be done with any existing technique for model-based diagnosis.

Two different types of design goals concerning the capability of distinguishing faults is proposed. The first goal is to design a sound and complete diagnosis system, i.e., a diagnosis system with the following property. For any observation, the diagnosis system computes

exactly the faults that together with the observation are consistent with the model. The second goal is specified by which faults that should be distinguished from other faults, and this is called the desired isolability.

Given any of these two design goals, theory and algorithms for selecting a minimum cardinality set of parts of the model are presented. Only parts with redundancy can be used for test construction and a key result is that there exists a sound and complete diagnosis system based on the set of all minimal parts with redundancy in the model. In differentialalgebraic models, it is in general difficult to analytically identify parts with redundancy, because it corresponds to variable elimination or projection. It is formally shown that redundant parts can be found by using a structural approach, i.e., to use only which variables that are included in each equation. In the structural approach, parts with more equations than unknowns are identified with efficient graph-theoretical tools. A key contribution is a new algorithm for finding all minimal parts with redundancy of the model. The efficiency of the algorithm is demonstrated on a truck engine model and compared to the computational complexity of previous algorithms.

In conclusion, tools for test selection have been developed. The selection is based on intuitive requirements such as soundness or isolability requirements specified by the diagnosis system designer. This leads to a more straightforward design of diagnosis systems, valuable engineering time can be saved, and the resulting diagnosis systems use minimum number of tests, i.e., the on-line computational complexity of the resulting diagnosis systems become low.

Place, publisher, year, edition, pages
Institutionen för systemteknik , 2006. , 275 p.
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1033
Keyword [en]
diagnosis, graph theory, structual methods, algorithms, fault isolation, complete, sound
National Category
Information Science
URN: urn:nbn:se:liu:diva-7417ISBN: 91-85523-32-1OAI: diva2:22420
Public defence
2006-10-13, Visionen, B-huset, Campus Valla, Linköpings universitet, Linköping, 10:15 (English)
Available from: 2006-09-25 Created: 2006-09-25 Last updated: 2009-03-04

Open Access in DiVA

fulltext(1666 kB)1004 downloads
File information
File name FULLTEXT01.pdfFile size 1666 kBChecksum SHA-1
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Krysander, Mattias
By organisation
Vehicular SystemsThe Institute of Technology
Information Science

Search outside of DiVA

GoogleGoogle Scholar
Total: 1004 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 1567 hits
ReferencesLink to record
Permanent link

Direct link