liu.seSearch for publications in DiVA
Change search
ReferencesLink to record
Permanent link

Direct link
A High Energy Efficient Mobile Fluid Power System: Novel System Layout and Measurements
Linköping University, Department of Mechanical Engineering, Fluid and Mechanical Engineering Systems. Linköping University, The Institute of Technology.ORCID iD: 0000-0002-6371-1390
MCD Parker Hannifin AB.
Linköping University, Department of Mechanical Engineering, Fluid and Mechanical Engineering Systems. Linköping University, The Institute of Technology.
2008 (English)Conference paper (Other academic)
Abstract [en]

This is one of the earliest publications of the proposed energy efficient individual metering system shown in chapter 5, section 5.3.3. This paper introduces the novel system design, which utilizes independent meter-in and meter-out valves. This system design has the potential to increase energy efficiency considerably in a system that consists of a pump  connected to more than one fluid power actuator. The system proposed here is not dependent on pressure transducers for either flow control or mode selection. The main difference between the work presented in this paper and earlier work is the control strategy. The output signal choices in the closed loops are new. Some functionality is kept in hardware to avoid  critical sensor dependency. The presented system uses pressure compensators to achieve desired flows.

Place, publisher, year, edition, pages
2008. 103-114 p.
Keyword [en]
efficiency, energy saving, mobile system, fluid power
National Category
Engineering and Technology
URN: urn:nbn:se:liu:diva-42262Local ID: 62135OAI: diva2:263118
Proceedings of the Sixth International Fluid Power Conference, IFK’08, March 31 - April 2, Dresden, Gemany
Available from: 2009-10-10 Created: 2009-10-10 Last updated: 2015-08-31Bibliographically approved
In thesis
1. Mobile Fluid Power Systems Design: with a Focus on Energy Efficiency
Open this publication in new window or tab >>Mobile Fluid Power Systems Design: with a Focus on Energy Efficiency
2010 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

This work deals with innovative energy efficient fluid power systems for mobile applications. The subjects taken up concern to what extent and how energy losses can be reduced in mobile working hydraulics systems. Various measures are available for increasing energy efficiency in these kinds of systems. Examples include:

Flow controlled systems The pump controller is switched from a load sensing toa displacement controlled one. The displacement is controlled in an open loopfashion directly from the operator’s demand signals. This reduces energy consumptionat the same time as dynamic issues that are attached to LS systemscan be avoided.

Individual metering valve systems Flexibility is increased by removing the mechanicalcoupling between the meter-in and meter-out orifices in directionalvalves. An overview of this kind of system is given in the thesis. A designproposal that has been implemented is also presented. Initial test results areshown. Patents for this particular system have been applied for.

Displacement control Metering losses are reduced by removing the directional valves.One pump is used for each load in such systems. This hardware layout involvesconsiderable changes compared to conventional systems. Displacementcontrolled systems are not studied in this work.

In mobile applications, overall efficiency is often poor and losses are substantial. The measures listed above can help improve this significantly in such applications. A flow dividing system can decrease energy consumption by about 10% and an individual metering system by about 20%. Losses in pump controlled systems are difficult to give a figure for; the losses are rather attached to the pumps and motors and not to the system layout. However, the losses for these systems are presumably even lower than for individual metering systems. The main focus in this work is on individual metering systems but questions about which components and so on are also treated. For example, the Valvistor valve concept has been studied as part of this work.


Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2010. 77 p.
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1339
National Category
Engineering and Technology
urn:nbn:se:liu:diva-61362 (URN)978-91-7393-304-9 (ISBN)
Public defence
2010-11-19, Planck, Fysikhuset, ing°ang 57, Campus Valla, Linköpings universitet, Linköping, 10:15 (English)
Available from: 2010-11-16 Created: 2010-11-16 Last updated: 2015-08-31Bibliographically approved

Open Access in DiVA

No full text

Search in DiVA

By author/editor
Eriksson, BjörnPalmberg, Jan-Ove
By organisation
Fluid and Mechanical Engineering SystemsThe Institute of Technology
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 1520 hits
ReferencesLink to record
Permanent link

Direct link