liu.seSearch for publications in DiVA
Change search
ReferencesLink to record
Permanent link

Direct link
Coherency strain engineered decomposition of unstable multilayer alloys for improved thermal stability
Linköping University, Department of Physics, Chemistry and Biology, Nanostructured Materials. Linköping University, The Institute of Technology.
Linköping University, Department of Physics, Chemistry and Biology, Nanostructured Materials. Linköping University, The Institute of Technology.
Linköping University, Department of Physics, Chemistry and Biology, Nanostructured Materials. Linköping University, The Institute of Technology.ORCID iD: 0000-0002-2286-5588
2013 (English)In: Journal of Applied Physics, ISSN 0021-8979, E-ISSN 1089-7550, Vol. 114, no 24, 244303- p.Article in journal (Refereed) Published
Abstract [en]

A concept to improve hardness and thermal stability of unstable multilayer alloys is presented based on control of the coherency strain such that the driving force for decomposition is favorably altered. Cathodic arc evaporated cubic TiCrAlN/Ti 1−x Cr x N multilayer coatings are used as demonstrators. Upon annealing, the coatings undergo spinodal decomposition into nanometer-sized coherent Ti- and Al-rich cubic domains which is affected by the coherency strain. In addition, the growth of the domains is restricted by the surrounding TiCrN layer compared to a non-layered TiCrAlN coating which together results in an improved thermal stability of the cubic structure. A significant hardness increase is seen during decomposition for the case with high coherency strain while a low coherency strain results in a hardness decrease for high annealing temperatures. The metal diffusion paths during the domain coarsening are affected by strain which in turn is controlled by the Cr-content (x) in the Ti 1−x Cr x N layers. For x = 0 the diffusion occurs both parallel and perpendicular to the growth direction but for x > =0.9 the diffusion occurs predominantly parallel to the growth direction. Altogether this study shows a structural tool to alter and fine-tune high temperature properties of multicomponent materials.

Place, publisher, year, edition, pages
American Institute of Physics (AIP), 2013. Vol. 114, no 24, 244303- p.
National Category
Materials Engineering
URN: urn:nbn:se:liu:diva-103072DOI: 10.1063/1.4851836ISI: 000329173200056OAI: diva2:686653
Swedish Foundation for Strategic Research
Available from: 2014-01-13 Created: 2014-01-13 Last updated: 2014-09-18Bibliographically approved
In thesis
1. Multicomponent Alloying for Improved Hard Coatings
Open this publication in new window or tab >>Multicomponent Alloying for Improved Hard Coatings
2014 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Coatings are vital to protect and to increase the productivity of cutting tools in high speed and dry cutting applications. During the cutting operation the temperature may exceed 1000 ºC it is therefore necessary that the coatings withstand high temperatures. A lot of development and research has been carried out during the last 30 years on finding new coating material systems providing enhanced properties such as adhesion, hardness and oxidation resistance at elevated temperatures. This thesis is based on multicomponent alloying of quaternary transition metal nitride hard coatings with a main focus on Ti-Cr-Al-N coatings. Many different coatings and compositions have been deposited using an industrial scale cathodic arc evaporation deposition system. All deposited coatings contain Al as this element is known to increase the hardness and the oxidation resistance of nitride coatings. The deterioration of the hardness in Al-containing nitride coatings is generally attributed to the transformation of cubic Al-N into hexagonal Al-N and the consequent domain coherency relaxation. This thesis investigates these phenomena on an atomic level providing a deeper understanding of and a way to engineer improved hard nitride coatings. The essence of this thesis is that by adding a third metal to a ternary nitride material system, for example one of the most frequently used Ti-Al-N, it is possible to tune and engineer the thermal stability of the cubic structure and the coherency strain which in turn affects the hardness and the oxidation resistance. The key point is that new intermediate phases in the decomposition process are generated so that the eventual detrimental phases are suppressed and delayed. More specifically, when Cr is added to the Ti-Al-N material system the coatings exhibit an age hardening process up to 1000 ºC caused by spinodal decomposition into coherent TiCr- and AlCr-rich cubic Ti-Cr-Al-N domains. This means that the unstable cubic Ti-Cr-Al-N phase decomposes via yet another unstable cubic Cr-Al-N phase before the detrimental hexagonal transformation of AlN takes place. The hardness is therefore retained up to a higher temperature compared to Ti-Al-N coatings.

By utilizing multicomponent alloying through addition of Ti to Cr-Al-N coatings the hardness is retained after annealing up to 1100 ºC. This is a dramatic improvement compared to Cr-Al-N coatings. Here the Ti addition promotes the competitive spinodal decomposition into TiCr- and Al-enriched domains suppressing the detrimental hexagonal AlN formation.

To investigate the effect of multicomponent alloying for other material systems with different mixing free energies and atomic sizes, Zr-containing, Zr-Cr-Al-N and Zr-Ti-Al-N, quaternary nitride coatings have also been deposited. For high Al- and high Zr-containing coatings the cubic solid solution structure is disrupted into a mix of nano-crystalline hexagonal and cubic phases with significantly lower hardness. The results show that the structure and hardness of these coatings are sensitive to the composition and in order to optimize the hardness and thermal stability the composition has to be fine-tuned. Altogether it is shown that through multicomponent alloying and through the control of the coherency strain it is possible to enhance the hardness and the oxidation resistance compared to the ternary system which may lead to new improved functional hard coatings.

Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2014. 65 p.
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1621
National Category
Physical Sciences Nano Technology
urn:nbn:se:liu:diva-110684 (URN)10.3384/diss.diva-110684 (DOI)978-91-7519-238-3 (print) (ISBN)
Public defence
2014-10-30, Planck, Fysikhuset, Camus Valla, Linköpings universitet, Linköping, 10:15 (English)
Available from: 2014-09-18 Created: 2014-09-18 Last updated: 2014-09-22Bibliographically approved

Open Access in DiVA

fulltext(3350 kB)133 downloads
File information
File name FULLTEXT01.pdfFile size 3350 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Other links

Publisher's full text

Search in DiVA

By author/editor
Forsén, RikardGhafoor, NaureenOdén, Magnus
By organisation
Nanostructured MaterialsThe Institute of Technology
In the same journal
Journal of Applied Physics
Materials Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 133 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 141 hits
ReferencesLink to record
Permanent link

Direct link