liu.seSearch for publications in DiVA
Change search
ReferencesLink to record
Permanent link

Direct link
All-printed diode operating at 1.6 GHz
Linköping University, Department of Science and Technology, Physics and Electronics. Linköping University, The Institute of Technology.
Linköping University, Department of Science and Technology. Linköping University, The Institute of Technology.
De La Rue Plc, Overton, Hampshire, UK .
Acreo AB, Norrköping, Sweden.
Show others and affiliations
2014 (English)In: Proceedings of the National Academy of Sciences of the United States of America, ISSN 0027-8424, E-ISSN 1091-6490, Vol. 111, no 33, 11943-11948 p.Article in journal (Refereed) Published
Abstract [en]

Printed electronics are considered for wireless electronic tags and sensors within the future Internet-of-things (IoT) concept. As a consequence of the low charge carrier mobility of present printable organic and inorganic semiconductors, the operational frequency of printed rectifiers is not high enough to enable direct communication and powering between mobile phones and printed e-tags. Here, we report an all-printed diode operating up to 1.6 GHz. The device, based on two stacked layers of Si and NbSi2 particles, is manufactured on a flexible substrate at low temperature and in ambient atmosphere. The high charge carrier mobility of the Si microparticles allows device operation to occur in the charge injection-limited regime. The asymmetry of the oxide layers in the resulting device stack leads to rectification of tunneling current. Printed diodes were combined with antennas and electrochromic displays to form an all-printed e-tag. The harvested signal from a Global System for Mobile Communications mobile phone was used to update the display. Our findings demonstrate a new communication pathway for printed electronics within IoT applications.

Place, publisher, year, edition, pages
National Academy of Sciences , 2014. Vol. 111, no 33, 11943-11948 p.
Keyword [en]
UHF; silicon particle
National Category
Electrical Engineering, Electronic Engineering, Information Engineering Physical Sciences
URN: urn:nbn:se:liu:diva-110476DOI: 10.1073/pnas.1401676111ISI: 000340438800027PubMedID: 25002504OAI: diva2:746967

Funding Agencies|Knut and Alice Wallenberg Foundation (Power Paper Project) [KAW 2011.0050]; Onnesjo Foundation; Swedish Research Council Linnaeus Grant LiLi-NFM; European Regional Development Fund through Tillvaxtverket (Project PEA-PPP)

Available from: 2014-09-15 Created: 2014-09-12 Last updated: 2016-04-12Bibliographically approved
In thesis
1. Addressability and GHz Operation in Flexible Electronics
Open this publication in new window or tab >>Addressability and GHz Operation in Flexible Electronics
2016 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

The discovery of conductive polymers in 1977 opened up a whole new path for flexible electronics. Conducting polymers and organic semiconductors are carbon rich compounds that are able to conduct charges while flexed and are compatible with low-cost and large-scale processes including printing and coating techniques. The conducting polymer has aided the rapidly expanding field of flexible electronics, leading to many new applications such as electronic skin, RFID tags, smart labels, flexible displays, implantable medical devices, and flexible sensors.

However, there are several remaining challenges in the production and implementation of flexible electronic materials and devices. The  conductivity of organic conductors and semiconductors is still orders of magnitude lower compared to their inorganic counterparts. In addition, non-flexible inorganic semiconductors still remain the materials of choice for high frequency applications; since the charge carrier mobility and thus operational speed of the organic materials are limited. Therefore, there remains a high demand to combine the high frequency operation of inorganic semiconductors with the flexible fabrication methods of organic systems for future electronics.

In addition to the challenges in the choice of materials in flexible electronics, the upscaling of the flexible devices and implementing them in circuits can also be complicated. Lack of non-linearity is an issue that arises when flexible devices with linear behavior need to be incorporated in an array or matrix form. Non-linearity is important for applications such as displays and memory arrays, where the devices are arranged as matrix cells addressed by their row and column number. If the behavior of cells in the matrix is linear, addressing each cell affects the adjacent cells. Therefore, inducing non-linearity and, consequently, addressability in such linear devices is the first step before scaling up into matrix schemes.

In this work, non-linear organic/inorganic hybrid devices are produced to overcome the limitations mentioned above and leverage the advantages of both organic and inorganic materials. Two novel methods are developed to incorporate non-flexible inorganic semiconductors into ultra-high frequency (UHF) flexible devices. In the first method, Si is ground into a powder with micrometer-sized particles and printed through standard screen printing. For the first time, allprinted flexible diodes operating in the GHz range are produced. The energy harvesting application of the printed diodes is demonstrated in a flexible circuit coupling an antenna and the display to the diode.

A second and simpler room-temperature method based on lamination was later developed, which further improves device performance and operational frequency. For the first time, a flexible semiconducting composite film consisting of Si micro-particles, glycerol, and nano-fibrillated cellulose is produced and used as the semiconducting layer of the UHF diode.

The diodes fabricated through both mentioned processes are demonstrated in energy harvesting applications in the GHz range; however, they can also serve as rectifiers or non-linear elements in any other flexible and UHF circuit.

Furthermore, a new approach is developed to induce non-linearity and hence addressability in linear devices in order to make their implementation in flexible matrix form feasible. This is accomplished by depositing a ferroelectric layer on a device electrode and thus controlling charge transfer through the electrode. The electrode current becomes limited to the charge displacement current established in the ferroelectric layer during polarization. Thus, the current does not follow the voltage linearly and non-linearity is induced in the device. The polarization voltage is dictated by the thickness of the ferroelectric layer. Therefore, the switching voltage of the device can be tuned by adjusting the ferroelectric layer thickness. In this work, the organic ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) is used due to its distinctive properties such as stability, high polarizability and simple processability. The polarization of P(VDF-TrFE) through an electrolyte and an electrophoretic liquid is investigated. In addition, a simple model is presented in order to understand the field and potential distribution, and the ferroelectric polarization, in the P(VDF-TrFE)-electrolyte contact. The induction of non-linearity through P(VDF-TrFE) is successfully demonstrated in novel addressable and bistable devices and memory elements such as non-linear electrophoretic display cells, organic ferroelectrochromic displays (FeOECDs), and ferroelectrochemical organic transistors (FeOECTs).

Place, publisher, year, edition, pages
Linköping: Linköping University Electronic Press, 2016. 58 p.
Linköping Studies in Science and Technology. Dissertations, ISSN 0345-7524 ; 1761
National Category
Physical Sciences Condensed Matter Physics Textile, Rubber and Polymeric Materials Materials Chemistry Other Electrical Engineering, Electronic Engineering, Information Engineering Polymer Chemistry
urn:nbn:se:liu:diva-127014 (URN)10.3384/diss.diva-127014 (DOI)978-91-7685-777-9 (Print) (ISBN)
Public defence
2016-05-13, K3, Kåkenhus, Campus Norrköping, Norrköping, 10:15 (English)
Available from: 2016-04-12 Created: 2016-04-12 Last updated: 2016-07-13Bibliographically approved

Open Access in DiVA

fulltext(1604 kB)446 downloads
File information
File name FULLTEXT01.pdfFile size 1604 kBChecksum SHA-512
Type fulltextMimetype application/pdf

Other links

Publisher's full textPubMed

Search in DiVA

By author/editor
Abdollahi Sani, NegarRobertsson, MatsLiu, XianjieFahlman, MatsCrispin, XavierEngquist, IsakBerggren, Magnus
By organisation
Physics and ElectronicsThe Institute of TechnologyDepartment of Science and TechnologySurface Physics and Chemistry
In the same journal
Proceedings of the National Academy of Sciences of the United States of America
Electrical Engineering, Electronic Engineering, Information EngineeringPhysical Sciences

Search outside of DiVA

GoogleGoogle Scholar
Total: 446 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 1187 hits
ReferencesLink to record
Permanent link

Direct link