Macroporous polymer films with long-range uniformity and biotinyl-moiety selective recognition sites have been developed. A hierarchical molecular imprinting strategy afforded significant enhancements in quartz crystal microbalance (QCM) sensitivities towards biotinylated compounds.
Rational design and informed development of nontoxic antifouling coatings requires a thorough understanding of the interactions between surfaces and fouling species. With more complex antifouling materials, such as composites or zwitterionic polymers, there follows also a need for better characterization of the materials as such. To further the understanding of the antifouling properties of charge-balanced polymers, we explore the properties of layered polyelectrolytes and their interactions with charged surfaces. These polymers were prepared via self-initiated photografting and photopolymerization (SIPGP); on top of a uniform bottom layer of anionic poly(methacrylic acid) (PMAA), a cationic poly(2-dimethylaminoethyl methacrylate) (PDMAEMA) thickness gradient was formed. Infrared microscopy and imaging spectroscopic ellipsometry were used to characterize chemical composition and swelling of the combined layer. Direct force measurements by colloidal probe atomic force microscopy were performed to investigate the forces between the polymer gradients and charged probes. The swelling of PMAA and PDMAEMA are very different, with steric and electrostatic forces varying in a nontrivial manner along the gradient. The gradients can be tuned to form a protein-resistant charge-neutral region, and we demonstrate that this region, where both electrostatic and steric forces are small, is highly compressed and the origin of the protein resistance of this region is most likely an effect of strong hydration of charged residues at the surface, rather than swelling or bulk hydration of the polymer. In the highly swollen regions far from charge-neutrality, steric forces dominate the interactions between the probe and the polymer. In these regions, the SIPGP polymer has qualitative similarities with brushes, but we were unable to quantitatively describe the polymer as a brush, supporting previous data suggesting that these polymers are cross-linked.
We report on the preparation and characterization of thin polyampholytic hydrogel gradient films permitting pH-controlled protein resistance via the regulation of surface charges. The hydrogel gradients are composed of cationic poly(2-aminoethyl methacrylate hydrochloride) (PAEMA), and anionic poly(2-carboxyethyl acrylate) (PCEA) layers, which are fabricated by self-initiated photografting and photopolymerization (SIPGP). Using a two-step UV exposure procedure, a polymer thickness gradient of one component is formed on top of a uniform layer of the oppositely charged polymer. The swelling of the gradient films in water and buffers at different pH were characterized by imaging spectroscopic ellipsometry. The surface charge distribution and steric interactions with the hydrogel gradients were recorded by direct force measurement with colloidal-probe atomic force microscopy. We demonstrate that formation of a charged polymer thickness gradient on top of a uniform layer of opposite charge can result in a region of charge-neutrality. This charge-neutral region is highly resistant to non-specific adsorption of proteins, and its location along the gradient can be controlled via the pH of the surrounding buffer. The pH-controlled protein adsorption and desorption was monitored in real-time by imaging surface plasmon resonance, while the corresponding redistribution of surface charge was confirmed by direct force measurements.
The effects of cathode modification by a conjugated polymer interlayer PFPA1 on the performance of reversed organic solar cells (substrate/cathode/active layer/transparent anode) based on different active material systems and different substrate electrodes are systematically investigated. A reduction of the work function irrespective of the substrate cathode used is observed upon the deposition of the PFPA1 interlayer, which is further related to an improved built-in electric field and open-circuit voltage. The amphiphilic character of the PFPA1 interlayer alters the surface energy of the substrate cathode, leading to the formation of a better active layer morphology aiding efficient exciton dissociation and photocurrent extraction in the modified solar cells. Hence, internal quantum efficiency is found to be significantly higher than that of their unmodified counterparts, while optically, the modified and unmodified solar cells are identical. Moreover, the deep highest occupied molecular orbital (HOMO) of the PFPA1 interlayer improves the selectivity for all investigated substrate cathodes, thus enhancing the fill factor.
In organic bulk-heterojunction solar cells, energy losses at the active layer/electrode interface are often observed. Modification of these interfaces with organic interlayers optimizes charge carrier injection and extraction and thus improves device performance. In this work, the effects of cathode modification by a conjugated polymer interlayer PFPA1 on the performance of reversed organic solar cells (substrate/cathode/active layer/transparent anode) based on different active material systems and different substrate electrodes are systematically investigated. A reduction of the work function irrespective of the substrate cathode used is observed upon the deposition of the PFPA1 interlayer; further related to an improved built-in electric field and open-circuit voltage. The amphiphilic character of the PFPA1 interlayer alters the surface energy of the substrate cathode, leading to the formation of a better active layer morphology aiding efficient exciton dissociation and photocurrent extraction in the modified solar cells. Hence, internal quantum efficiency is found significantly higher than that of their unmodified counterparts, while optically, the modified and unmodified solar cells are identical. Moreover, the deep HOMO of the PFPA1 interlayer improves the selectivity for all investigated substrate cathodes, thus enhancing the fill factor. We demonstrate a possibility of improving photovoltaic performance of reversed solar cells via a simple and universal interface modification and provide the basic guidelines for development and characterization of interface materials for organic solar cells in general.
Adhesive proteins of barnacle cement have potential as environmentally friendly adhesives owing to their ability to adhere to various substrates in aqueous environments. By understanding the taxonomic breath of barnacles with different lifestyles, we may uncover commonalities in adhesives produced by these specialized organisms. The 19 kDa cement protein (cp19k) of the stalked barnacle Pollicipes pollicipes was expressed in Escherichia coli BL21 to investigate its adhesive properties. Initial expression of hexahistidine-tagged protein (rPpolcp19k-his) yielded low levels of insoluble protein. Co-overproduction of E. coli molecular chaperones GroEL-GroES and trigger factor (TF) increased soluble protein yields, although TF co-purified with the target protein (TF-rPpolcp19k-his). Surface coat analysis revealed high levels of adsorption of the TF-rPpolcp19k-his complex and of purified E. coli TF on both hydrophobic and hydrophilic surfaces, while low levels of adsorption were observed for rPpolcp19k-his. Tag-free rPpolcp19k protein also exhibited low adsorption compared to fibrinogen and Cell-Tak controls on hydrophobic, neutral hydrophilic and charged self-assembled monolayers under surface plasmon resonance assay conditions designed to mimic the barnacle cement gland or seawater. Because rPpolcp19k protein displays low adhesive capability, this protein is suggested to confer the ability to self-assemble into a plaque within the barnacle cement complex. This article is part of the theme issue Transdisciplinary approaches to the study of adhesion and adhesives in biological systems.
PEDOT-Tos is one of the conducting polymers that displays the most promising thermoelectric properties. Until now, it has been utterly difficult to control all the synthesis parameters and the morphology governing the thermoelectric properties. To improve our understanding of this material, we study the variation in the thermoelectric properties by a simple acido-basic treatment. The emphasis of this study is to elucidate the chemical changes induced by acid (HCl) or base (NaOH) treatment in PEDOT-Tos thin films using various spectroscopic and structural techniques. We could identify changes in the nanoscale morphology due to anion exchange between tosylate and Cl- or OH-. But, we identified that changing the pH leads to a tuning of the oxidation level of the polymer, which can explain the changes in thermoelectric properties. Hence, a simple acid-base treatment allows finding the optimum for the power factor in PEDOT-Tos thin films.
Interaction of zoospores of Ulva linza with cationic, arginine-rich oligopeptide self-assembled monolayers (SAMs) is characterized by rapid settlement. Some spores settle (ie permanently attach) in a normal manner involving the secretion of a permanent adhesive, retraction of the flagella and cell wall formation, whilst others undergo pseudosettlement whereby motile spores are trapped (attached) on the SAM surface without undergoing the normal metamorphosis into a settled spore. Holographic microscopy was used to record videos of swimming zoospores in the vicinity of surfaces with different cationic oligopeptide concentrations to provide time-resolved insights into processes associated with attachment of spores. The data reveal that spore attachment rate increases with increasing cationic peptide content. Accordingly, the decrease in swimming activity in the volume of seawater above the surface accelerated with increasing surface charge. Three-dimensional trajectories of individual swimming spores showed a hit and stick motion pattern, exclusively observed for the arginine-rich peptide SAMs, whereby spores were immediately trapped upon contact with the surface.
Lysosomes are acidic organelles essential for degradation, signalling and cell homoeostasis. In addition, they play a key role in cell death. Permeabilization of the lysosomal membrane and release of hydrolytic enzymes to the cytosol accompanies apoptosis signalling in several systems. The regulatory mechanism of lysosomal stability is, however, poorly understood. Lipophilic or amphiphilic compounds with a basic moiety will become protonated and trapped within lysosomes, and such lysosomotropic behaviour is also found in many pharmacological drugs. The natural sphingolipid sphingosine exhibits lysosomotropic detergent ability and is an endogenous candidate for controlling lysosomal membrane permeabilization. The lysosomotropic properties of certain detergents might be of use in lysosome-targeting anticancer drugs and drug delivery system in the future. The present review summarizes the current knowledge on the targeting and permeabilizing properties of lysosomotropic detergents from a cellular and physicochemical perspective.
Lysosomotropic detergents (LDs) selectively rupture lysosomal membranes through mechanisms that have yet to be characterized. A consensus view, currently, holds that LDs, which are weakly basic, diffuse across cellular membranes as monomers in an uncharged state, and via protonation in the acidic lysosomal compartment, they become trapped, accumulate, and subsequently solubilize the membrane and induce lysosomal membrane permeabilization. Here we demonstrate that the lysosomotropic detergent O-methyl-serine dodecylamide hydrochloride (MSDH) spontaneously assembles into vesicles at, and above, cytosolic pH, and that the vesicles disassemble as the pH reaches 6.4 or lower. The aggregation commences at concentrations below the range of those used in cell studies. Assembly and disassembly of the vesicles was studied via dynamic light scattering, zeta potential measurements, cryo-TEM, and fluorescence correlation spectroscopy and was found to be reversible via control of the pH. Aggregation of MSDH into closed vesicles under cytosolic conditions is at variance with the commonly held view of LD behavior, and we propose that endocytotic pathways should be considered as possible routes of LD entry into lysosomes. We further demonstrate that MSDH vesicles can be loaded with fluorophores via a solution transition from low to high pH, for subsequent release when the pH is lowered again. The ability to encapsulate molecular cargo into MSDH vesicles together with its ability to disaggregate at low pH and to permeabilize the lysosomal membrane presents an intriguing possibility to use MSDH as a delivery system.
O-methyl-serine dodecylamine hydrochloride (MSDH) is a detergent that accumulates selectively in lysosomes, a so-called lysosomotropic detergent, with unexpected chemical properties. At physiological pH, it spontaneously forms vesicles, which disassemble into small aggregates (probably micelles) below pH 6.4. In this study, we characterize the interaction between MSDH and liposomes at different pH and correlate the findings to toxicity in human fibroblasts. We find that the effect of MSDH on lipid membranes is highly pH-dependent. At neutral pH, the partitioning of MSDH into the liposome membrane is immediate and causes the leakage of small fluorophores, unless the ratio between MSDH and lipids is kept low. At pH 5, the partitioning of MSDH into the membrane is kinetically impeded since MSDH is charged and a high ratio between MSDH and the lipids is required to permeabilize the membrane. When transferred to cell culture conditions, the ratio between MSDH and plasma membrane lipids must therefore be low, at physiological pH, to maintain plasma membrane integrity. Transmission electron microscopy suggests that MSDH vesicles are taken up by endocytosis. As the pH of the endosomal compartment progressively drops, MSDH vesicles disassemble, leading to a high concentration of increasingly charged MSDH in small aggregates inside the lysosomes. At sufficiently high MSDH concentrations, the lysosome is permeabilized, the proteolytic content released to the cytosol and apoptotic cell death is induced.
We investigated the influence of backbone regiochemistry on the conductivity, charge density, and polaron structure in the widely studied n-doped donor-acceptor polymer poly[N,N-bis(2-octyldodecyl)-1,4,5,8-naphthalenediimide-2,6-diyl]-alt-5,5-(2,2-bithiophene) [P-(NDI2OD-T2)]. In contrast to classic semicrystalline polymers such as poly(3-hexylthiophene) (P3HT), the regioirregular (RI) structure of the naphthalenediimide (NDI)-bithiophene (T2) backbone does not alter the intramolecular steric demand of the chain versus the regioregular (RR) polymer, yielding RI-P(NDI2OD-T2) with similar energetics and optical features as its RR counterpart. By combining the electrical, UV-vis/infrared, X-ray diffraction, and electron paramagnetic resonance data and density functional theory calculations, we quantitatively characterized the conductivity, aggregation, crystallinity, and charge density, and simulated the polaron structures, molecular vibrations, and spin density distribution of RR-/RI-P(NDI2OD-T2). Importantly, we observed that RI-P(NDI2OD-T2) can be doped to a greater extent compared to its RR counterpart. This finding is remarkable and contrasts benchmark P3HT, allowing us to uniquely study the role of regiochemistry on the charge-transport properties of n-doped donor-acceptor polymers.
Changes in the contact angle between conjugated polymers surface poly(3-hexylthiophene) [P3HT] and poly(3,4-ethylenedioxythiophene) (PEDOT) upon electrochemical doping−dedoping in aqueous electrolyte were determined in situ using a Wilhelmy plate tensiometer in an electrochemical cell. The hydrophobic P3HT was less hydrophobic in the oxidized state than in the neutral state; the more hydrophilic PEDOT was less hydrophilic in the oxidized state than when neutral. The tensiometry results were in good agreement with those measured by contact angle goniometry, and further corroborated by the capillary rise upon doping in a fluid cell with two parallel polymer coated plates, another in situ dynamic determination method. The contact angle changes depend on doping potential, electrolyte type, and concentration. We also deconvoluted the surface energy into components of van der Waals and acid−base interactions, using three probe liquids on the polymer surfaces, ex situ the electrochemical cell. The methods and the obtained results are relevant for the science and technology areas of printed electronics and electrochemical devices and for the understanding of surface energy modification by electrochemical doping.
The stability of organic solar cells (OSCs) is critical for practical applications of this emerging technology. Unfortunately, in spite of intensive investigations, the degradation mechanisms in OSCs have not been clearly understood yet. In this report, we employ a range of spectroscopic and transport measurements, coupled with drift-diffusion modelling, to investigate the light-induced degradation mechanisms of fullerene-based OSCs. We find that trap states formed in the fullerene phase under illumination play a critical role in the degradation of the open-circuit voltage (V-OC) in OSCs. Our results indicate that the degradation is intrinsic to the fullerenes in OSCs and that alternative acceptor materials are desired for the development of stable OSCs.
Transparent organic electrodes printed from high-conductivity PEDOT:PSS have become essential for upscaling all-carbon based, low-cost optoelectronic devices. In the printing process, low-work-function PEDOT:PSS electrodes (cathode) are achieved by coating an ultra-thin, non-conjugated polyelectrolyte that is rich in amine groups, such as poly(ethylene imine) (PEI) or its ethoxylated derivative (PEIE), onto PEDOT:PSS surfaces. Here, we mapped the physical and chemical processes that occur at the interface between thin PEIx (indicating either PEI or PEIE) and PEDOT:PSS during printing. We identify that there is a dedoping effect of PEDOT induced by the PEIx. Using infrared spectroscopy, we found that the amine-rich PEIx can form chemical bonds with the dopant, PSS. At lower PSS concentration, PEIx also shows an electron-transfer effect to the charged PEDOT chain. These interface reactions lock the surface morphology of PEDOT:PSS, preventing the redistribution of PSS, and reduce the work function. Subsequent exposure to oxygen during the device fabrication process, on the other hand, can result in redoping of the low-work-function PEDOT:PSS interface, causing problems for printing reproducible devices under ambient conditions.
Biofouling is still a major challenge in the application of nanofiltration and reverse osmosis membranes. Here we present a platform approach for environmentally friendly biofouling control using a combination of a hydrogel-coated feed spacer and two-phase flow cleaning. Neutral (polyHEMA-co-PEG(10)MA), cationic (polyDMAEMA) and anionic (polySPMA) hydrogels have been successfully grafted onto polypropylene (PP) feed spacers via plasma-mediated UV-polymerization. These coatings maintained their chemical stability after 7 days incubation in neutral (pH 7), acidic (pH 5) and basic (pH 9) environments. Anti-biofouling properties of these coatings were evaluated by Escherichia coli attachment assay and nanofiltration experiments at a TMP of 600 kPag using tap water with additional nutrients as feed and by using optical coherence tomography. Especially the anionic polySPMA-coated PP feed spacer shows reduced attachment of E. coli and biofouling in the spacer-filled narrow channels resulting in delayed biofilm growth. Employing this highly hydrophilic coating during removal of biofouling by two-phase flow cleaning also showed enhanced cleaning efficiency, feed channel pressure drop and flux recoveries. The strong hydrophilic nature and the presence of negative charge on polySPMA are most probably responsible for the improved antifouling behavior. A combination of polySPMA-coated PP feed spacers and two-phase flow cleaning therefore is promising and an environmentally friendly approach to control biofouling in NF/RO systems employing spiral-wound membrane modules.
The flatworm Macrostomum lignano features a duo-gland adhesive system that allows it to repeatedly attach to and release from substrates in seawater within a minute. However, little is known about the molecules involved in this temporary adhesion. In this study, we show that the attachment of M. lignano relies on the secretion of two large adhesive proteins, M. lignano adhesion protein 1 (Mlig-ap1) and Mlig-ap2. We revealed that both proteins are expressed in the adhesive gland cells and that their distribution within the adhesive footprints was spatially restricted. RNA interference knockdown experiments demonstrated the essential function of these two proteins in flatworm adhesion. Negatively charged modified sugars in the surrounding water inhibited flatworm attachment, while positively charged molecules impeded detachment. In addition, we found that M. lignano could not adhere to strongly hydrated surfaces. We propose an attachment-release model where Mlig-ap2 attaches to the substrate and Mlig-ap1 exhibits a cohesive function. A small negatively charged molecule is secreted that interferes with Mlig-ap1, inducing detachment. These findings are of relevance for fundamental adhesion science and efforts to mitigate biofouling. Further, this model of flatworm temporary adhesion may serve as the starting point for the development of synthetic reversible adhesion systems for medicinal and industrial applications.
A common way of determining the majority charge carriers of pristine and doped semiconducting polymers is to measure the sign of the Seebeck coefficient. However, a polarity change of the Seebeck coefficient has recently been observed to occur in highly doped polymers. Here, it is shown that the Seebeck coefficient inversion is the result of the density of states filling and opening of a hard Coulomb gap around the Fermi energy at high doping levels. Electrochemical n-doping is used to induce high carrier density (>1 charge/monomer) in the model system poly(benzimidazobenzophenanthroline) (BBL). By combining conductivity and Seebeck coefficient measurements with in situ electron paramagnetic resonance, UV-vis-NIR, Raman spectroelectrochemistry, density functional theory calculations, and kinetic Monte Carlo simulations, the formation of multiply charged species and the opening of a hard Coulomb gap in the density of states, which is responsible for the Seebeck coefficient inversion and drop in electrical conductivity, are uncovered. The findings provide a simple picture that clarifies the roles of energetic disorder and Coulomb interactions in highly doped polymers and have implications for the molecular design of next-generation conjugated polymers.
Marine biofouling has detrimental effects on the environment and economy, and current antifouling coatings research is aimed at environmentally benign, non-toxic materials. The possibility of using contact-active coatings is explored, by considering the antialgal activity of cationic poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) brushes. The antialgal activity was investigated via zoospore settlement and sporeling growth assays of the marine algae Ulva linza and U. lactuca. The assay results for PDMAEMA brushes were compared to those for anionic and neutral surfaces. It was found that only PDMAEMA could disrupt zoospores that come into contact with it, and that it also inhibits the subsequent growth of normally settled spores. Based on the spore membrane properties, and characterization of the PDMAEMA brushes over a wide pH range, it is hypothesized that the algicidal mechanisms are similar to the bactericidal mechanisms of cationic polymers, and that further development could lead to successful contact-active antialgal coatings.
The resistance of charged polymers to biofouling was investigated by subjecting cationic (PDMAEMA), anionic (PSPMA), neutral (PHEMA-co-PEG10MA), and zwitterionic (PSBMA) brushes to assays testing protein adsorption; attachment of the marine bacterium Cobetia marina; settlement and adhesion strength of zoospores of the green alga Ulva linza; settlement of barnacle (Balanus amphitrite and B. improvisus) cypris larvae; and field immersion tests. Several results go beyond the expected dependence on direct electrostatic attraction; PSPMA showed good resistance towards attachment of C. marina, low settlement and adhesion of U. linza zoospores, and significantly lower biofouling than on PHEMA-co-PEG10MA or PSBMA after a field test for one week. PDMAEMA showed potential as a contact-active anti-algal coating due to its capacity to damage attached spores. However, after field testing for eight weeks, there were no significant differences in biofouling coverage among the surfaces. While charged polymers are unsuitable as antifouling coatings in the natural environment, they provide valuable insights into fouling processes, and are relevant for studies due to charging of nominally neutral surfaces.
Understanding how surface physicochemical properties influence the settlement and adhesion of marine fouling organisms is important for the development of effective and environmentally benign marine antifouling coatings. We demonstrate that the thickness of random poly(HEMA-co-PEG(10)DMA) copolymer brushes affect antifouling behavior. Films of thicknesses ranging from 50 to 1000 angstrom were prepared via surface-initiated atom-transfer radical polymerization and characterized using infrared spectroscopy, ellipsometry, atomic force microscopy and contact angle measurements. The fouling resistance of these films was investigated by protein adsorption, attachment of the marine bacterium Cobetia marina, settlement and strength of attachment tests of zoospores of the marine alga Ulva linza and static immersion field tests. These assays show that the polymer film thickness influenced the antifouling performance, in that there is an optimum thickness range, 200-400 angstrom (dry thickness), where fouling of all types, as well as algal spore adhesion, was lower. Field test results also showed lower fouling within the same thickness range after 2 weeks of immersion. Studies by quartz crystal microbalance with dissipation and underwater captive bubble contact angle measurements show a strong correlation between lower fouling and higher hydration, viscosity and surface energy of the poly(HEMA-co-PEG(10)MA) brushes at thicknesses around 200-400 angstrom. We hypothesize that the reduced antifouling performance is caused by a lower hydration capacity of the polymer for thinner films, and that entanglement and crowding in the film reduces the conformational freedom, hydration capacity and fouling resistance for thicker films.
Polyampholytic poly(2-aminoethyl methacrylate-co-sulfopropyl methacrylate) (p(AEMA-co-SPMA)) thin films were prepared by self-initiated photopolymerization and photografting (SIPGP) and are demonstrated to be a potential alternative to films prepared from zwitterionic poly(sulfobetaine methacrylate) (pSBMA) for antifouling applications. SIPGP allows polymerization from aqueous solutions containing only monomers, implying that p(AEMA-co-SPMA) thin films can be prepared simply and inexpensively without the risk of introducing potentially toxic substances necessary in many controlled polymerization reactions. For the polymers, wettabilities were studied by contact angle goniometry, the compositions of the films were determined by infrared and X-ray photoelectron spectroscopies, and streaming current measurements were used to assess their net charge. The antibiofouling properties were compared via adsorption of fibrinogen and bovine serum albumin, settlement of algal zoospores, and the growth of sporelings of the marine alga Ulva lactuca. The fouling of the p(AEMA-co-SPMA) copolymer was in several respects similar to that of the zwitterionic pSBMA and suggests that it is potentially suitable for applications under high-salinity conditions, such as marine or physiological environments.
Lipid bilayers, forming the outer barrier of cells, display a wide array of proteins and carbohydrates for modulating interfacial biological interactions. Formed by the spontaneous self-assembly of lipid molecules, these bilayers feature liquid crystalline order, while retaining a high degree of lateral mobility. Studies of these dynamic phenomena have been hampered by the fragility and instability of corresponding biomimetic cell membrane models. Here, we present the construct of a series of oligoethylene glycol-terminated reversible self-assembled monolayers (rSAMs) featuring lipid-bilayer-like fluidity, while retaining air and protein stability and resistance. These robust and ordered layers were prepared by simply immersing a carboxylic acid terminated self-assembled monolayer into 5-50 mu M aqueous omega-(4-ethylene glycol-phenoxy)-alpha-(4-amidinophenoxy)decane solutions. It is anticipated that this new class of robust and fluidic two-dimensional biomimetic surfaces will impact the design of rugged cell surface mimics and high-performance biosensors.
Cells adhering onto surfaces sense and respond to chemical and physical surface features. The control over cell adhesion behavior influences cell migration, proliferation, and differentiation, which are important considerations in biomaterial design for cell culture, tissue engineering, and regenerative medicine. Here, we report on a supramolecular-based approach to prepare reversible self-assembled monolayers (rSAMs) with tunable lateral mobility and dynamic control over surface composition to regulate cell adhesion behavior. These layers were prepared by incubating oxoacid-terminated thiol SAMs on gold in a pH 8 HEPES buffer solution containing different mole fractions of omega-(ethylene glycol),(2-)(4)- and omega-(GRGDS)-, alpha-benzamidino bolaamphiphiles. Cell shape and morphology were influenced by the strength of the interactions between the amidine-functionalized amphiphiles and the oxoacid of the underlying SAMs. Dynamic control over surface composition, achieved by the addition of inert filler amphiphiles to the RGD-functionalized rSAMs, reversed the cell adhesion process. In summary, rSAMs featuring mobile bioactive ligands offer unique capabilities to influence and control cell adhesion behavior, suggesting a broad use in biomaterial design, tissue engineering, and regenerative medicine.
Tunicates populate a great variety of marine underwater substrates worldwide and represent a significant concern in marine shipping and aquaculture. Adhesives are secreted from the anterior papillae of their swimming larvae, which attach and metamorphose into permanently adhering, filter-feeding adults. We recently described the cellular composition of the sensory adhesive organ of the model tunicate Ciona intestinalis in great detail. Notably, the adhesive secretions of collocytes accumulate at the tip of the organ and contain glycoproteins. Here, we further explore the components of adhesive secretions and have screened for additional specificities that may influence adhesion or cohesion of the Ciona glue, including other carbohydrate moieties, catechols and substrate properties. We found a distinct set of sugar residues in the glue recognized by specific lectins with little overlap to other known marine adhesives. Surprisingly, we also detect catechol residues that likely originate from an adjacent cellular reservoir, the test cells. Furthermore, we provide information on substrate preferences where hydrophobicity outperforms charge in the attachment. Finally, we can influence the settlement process by the addition of hydrophilic heparin. The further analysis of tunicate adhesive strategies should provide a valuable knowledge source in designing physiological adhesives or green antifoulants. This article is part of the theme issue Transdisciplinary approaches to the study of adhesion and adhesives in biological systems.
The interactions between electron donors (D) and acceptors (A) of organic semiconducting molecules are of great interest to organic electronics, e.g. electrical doping of organic semiconductors (OSCs), photo-generation of charges in organic solar cells, and light-emitting/detecting devices based on OSCs. A blend of D/A OSC is typically characterized by weak van der Waals interactions or integer charge transfer (ICT) between neighboring D/A molecules. In between these two scenarios of physical blends and ICT complexes, orbital hybridization between adjacent D/A molecules serves as a third alternative, characterized by an in situ formation of a ground state complex featuring partial charge transfer between participating donor and acceptor molecules. In this work is presented a comprehensive experimental study on partial charge-transfer complex (CPX) formed via orbital hybridization. Thiophenes and phthalocyanines are used as electron donors, while acceptor molecules of different geometries and electron affinities are employed with the aim to clarify how orbital symmetry, energy level alignment and steric hindrance affect orbital hybridization and subsequent tuning of the optical band-gap into the near infrared (NIR) region.