Future brain-computer interfaces will require local and highly individualized signal processing of fully integrated electronic circuits within the nervous system and other living tissue. New devices will need to be developed that can receive data from a sensor array, process these data into meaningful information, and translate that information into a format that can be interpreted by living systems. Here, the first example of interfacing a hardware-based pattern classifier with a biological nerve is reported. The classifier implements the Widrow-Hoff learning algorithm on an array of evolvable organic electrochemical transistors (EOECTs). The EOECTs channel conductance is modulated in situ by electropolymerizing the semiconductor material within the channel, allowing for low voltage operation, high reproducibility, and an improvement in state retention by two orders of magnitude over state-of-the-art OECT devices. The organic classifier is interfaced with a biological nerve using an organic electrochemical spiking neuron to translate the classifiers output to a simulated action potential. The latter is then used to stimulate muscle contraction selectively based on the input pattern, thus paving the way for the development of adaptive neural interfaces for closed-loop therapeutic systems.

Ice formation detection is important in telecommunications and aeronautics, e.g., ice on the wings of an aircraft affects its aerodynamic performance and leads to fatal accidents. While many types of sensors exist, resistive sensors for ice detection have been poorly explored. They are however attractive because of their simplicity and the possibility to install an array of sensors on large areas to map the ice formation on wings. Hygroscopic ionic conductors have been demonstrated for resistive ice sensing but their high resistance prevents the readout of sensor arrays. In this work, mixed ionic-electronic polymer conductors (MIEC) are considered for the first time for ice detection. The polymer blend poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) is solution deposited on a pair of electrodes. The sensor displays an abrupt rise in electrical resistance during the transition phase between water liquid to solid. It is proposed that the morphology and electronic transport in PEDOT are affected by the freezing event because the absorbed water in the PSS-rich phase undergoes dilatation upon forming ice crystals. For the aeronautics application, successful tests of integration of sensing layer in pre-preg layers of aeronautical grade and freezing detection are carried out to validate the ice detection principle.

Organic electrochemical transistors (OECTs) are being researched for various applications, ranging from sensors to logic gates and neuromorphic hardware. To meet the requirements of these diverse applications, the device fabrication process must be compatible with flexible and scalable digital techniques. Here, we report a direct-write additive process to fabricate fully 3D-printed OECTs, using 3D printable conducting, semiconducting, insulating, and electrolyte inks. These 3D-printed OECTs, which operate in the depletion mode, can be fabricated on flexible substrates, resulting in high mechanical and environmental stability. The 3D-printed OECTs have good dopamine biosensing capabilities (limit of detection down to 6 mu M without metal gate electrodes) and show long-term (similar to 1 h) synapse response, indicating their potential for various applications such as sensors and neuromorphic hardware. This manufacturing strategy is suitable for applications that require rapid design changes and digitally enabled direct-write techniques.

The interfacial energetics are known to play a crucial role in organic diodes, transistors, and sensors. Designing the metal-organic interface has been a tool to optimize the performance of organic (opto)electronic devices, but this is not reported for organic thermoelectrics. In this work, it is demonstrated that the electrical power of organic thermoelectric generators (OTEGs) is also strongly dependent on the metal-organic interfacial energetics. Without changing the thermoelectric figure of merit (ZT) of polythiophene-based conducting polymers, the generated power of an OTEG can vary by three orders of magnitude simply by tuning the work function of the metal contact to reach above 1000 mu W cm(-2). The effective Seebeck coefficient (S-eff) of a metal/polymer/metal single leg OTEG includes an interfacial contribution (V-inter/Delta T) in addition to the intrinsic bulk Seebeck coefficient of the polythiophenes, such that S-eff = S + V-inter/Delta T varies from 22.7 mu V K-1 [9.4 mu V K-1] with Al to 50.5 mu V K-1 [26.3 mu V K-1] with Pt for poly(3,4-ethylenedioxythiophene):p-toluenesulfonate [poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate)]. Spectroscopic techniques are used to reveal a redox interfacial reaction affecting locally the doping level of the polymer at the vicinity of the metal-organic interface and conclude that the energetics at the metal-polymer interface provides a new strategy to enhance the performance of OTEGs.

Biointegrated neuromorphic hardware holds promise for new protocols to record/regulate signalling in biological systems. Making such artificial neural circuits successful requires minimal device/circuit complexity and ion-based operating mechanisms akin to those found in biology. Artificial spiking neurons, based on silicon-based complementary metal-oxide semiconductors or negative differential resistance device circuits, can emulate several neural features but are complicated to fabricate, not biocompatible and lack ion-/chemical-based modulation features. Here we report a biorealistic conductance-based organic electrochemical neuron (c-OECN) using a mixed ion-electron conducting ladder-type polymer with stable ion-tunable antiambipolarity. The latter is used to emulate the activation/inactivation of sodium channels and delayed activation of potassium channels of biological neurons. These c-OECNs can spike at bioplausible frequencies nearing 100 Hz, emulate most critical biological neural features, demonstrate stochastic spiking and enable neurotransmitter-/amino acid-/ion-based spiking modulation, which is then used to stimulate biological nerves in vivo. These combined features are impossible to achieve using previous technologies.

Conjugated polymers with oligoether side chains are promisingmixedionic-electronic conductors, but they tend to feature a low glasstransition temperature and hence a low elastic modulus, which preventstheir use if mechanical robust materials are required. Carboxymethylatedcellulose nanofibrils (CNF) are found to be a suitable reinforcingagent for a soft polythiophene with tetraethylene glycol side chains.Dry nanocomposites feature a Youngs modulus of more than 400MPa, which reversibly decreases to 10 MPa or less upon passive swellingthrough water uptake. The presence of CNF results in a slight decreasein electronic mobility but enhances the ionic mobility and volumetriccapacitance, with the latter increasing from 164 to 197 F cm(-3) upon the addition of 20 vol % CNF. Overall, organic electrochemicaltransistors (OECTs) feature a higher switching speed and a transconductancethat is independent of the CNF content up to at least 20 vol % CNF.Hence, CNF-reinforced conjugated polymers with oligoether side chainsfacilitate the design of mechanically adaptive mixed ionic-electronicconductors for wearable electronics and bioelectronics.

The first Telluride Science meeting (formerly TSRC) on organic mixed ionic and electronic conductors (OMIECs), Oct 3-7, 2022, brought together researchers across the field to understand the fundamental processes and identify out-standing questions related to this exciting class of materials. OMIECs are organic materials that promote the transport of mobile electronic charge carriers while simultaneously supporting ionic transport and ionic-electronic coupling. These properties open up broad areas of applications from energy to bioelectronics. Devices include batteries, supercapacitors, actuators, electrochromic displays, and organic electrochemical transistors (OECTs). They possess the key strengths of traditional organic electronic materials, such as synthetic tunability and low-temperature processing. Despite the recent advances in devices and applications achieved with such materials, many challenges and gaps in understanding remain. These topics hold the key to designing next-generation materials and devices that continue to push the limits of performance and stability and facilitate novel functionality. This perspective aims to summarize the current understanding, conversations, and debates that made this TSRC particularly engaging, enabling new directions and searching for missing pieces of the OMIEC puzzle. This perspective offers insights from discussions conducted during the Telluride Science meeting on organic mixed ionic and electronic conductors, outlining the challenges associated with understanding the behavior of this intriguing materials class.

A conjugated-polymer-based n-type yarn for thermoelectric textiles is presented. Thermoelectric textile devices are intriguing power sources for wearable electronic devices. The use of yarns comprising conjugated polymers is desirable because of their potentially superior mechanical properties compared to other thermoelectric materials. While several examples of p-type conducting yarns exist, there is a lack of polymer-based n-type yarns. Here, a regenerated cellulose yarn is spray-coated with an n-type conducting-polymer-based ink composed of poly(benzimidazobenzophenanthroline) (BBL) and poly(ethyleneimine) (PEI). The n-type yarns display a bulk electrical conductivity of 8 x 10(-3) S cm(-1) and Seebeck coefficient of -79 mu V K-1. A promising level of air-stability for at least 13 days can be achieved by applying an additional thermoplastic elastomer coating. A prototype in-plane thermoelectric textile, produced with the developed n-type yarns and p-type yarns, composed of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)-coated regenerated cellulose, displays a stable device performance in air for at least 4 days with an open-circuit voltage per temperature difference of 1 mV degrees C-1. Evidently, polymer-based n-type yarns are a viable component for the construction of thermoelectric textile devices.

Organic electrochemical transistors (OECTs) are a rapidly advancing technology that plays a crucial role in the development of next-generation bioelectronic devices. Recent advances in p-type/n-type organic mixed ionic-electronic conductors (OMIECs) have enabled power-efficient complementary OECT technologies for various applications, such as chemical/biological sensing, large-scale logic gates, and neuromorphic computing. However, ensuring long-term operational stability remains a significant challenge that hinders their widespread adoption. While p-type OMIECs are generally more stable than n-type OMIECs, they still face limitations, especially during prolonged operations. Here, we demonstrate that simple methylation of the pyrrole-benzothiazine-based (PBBT) ladder polymer backbone results in stable and high-performance p-type OECTs. The methylated PBBT (PBBT-Me) exhibits a 25-fold increase in OECT mobility and an impressive 36-fold increase in & mu;C* (mobility x volumetric capacitance) compared to the non-methylated PBBT-H polymer. Combining the newly developed PBBT-Me with the ladder n-type poly(benzimidazobenzophenanthroline) (BBL), we developed complementary inverters with a record-high DC gain of 194 V V-1 and excellent stability. These state-of-the-art complementary inverters were used to demonstrate leaky integrate-and-fire type organic electrochemical neurons (LIF-OECNs) capable of biologically relevant firing frequencies of about 2 Hz and of operating continuously for up to 6.5 h. This achievement represents a significant improvement over previous results and holds great potential for developing stable bioelectronic circuits capable of in-sensor computing.

Operational stability is essential for the success of organic electrochemical transistors (OECTs) in bioelectronics. The oxygen reduction reaction (ORR) is a common electrochemical side reaction that can compromise the stability of OECTs, but the relationship between ORR and materials degradation is poorly understood. In this study, the impact of ORR on the stability and degradation mechanisms of thiophene-based OECTs is investigated. The findings show that an increase in pH during ORR leads to the degradation of the polymer backbone. By using a protective polymer glue layer between the semiconductor channel and the aqueous electrolyte, ORR is effectively suppressed and the stability of the OECTs is significantly improved, resulting in current retention of nearly 90% for & AP;2 h cycling in the saturation regime.

Ladder-type conjugated polymers exhibit a remarkable performance in (opto)electronic devices. Their double-stranded planar structure promotes an extended pi-conjugation compared to inter-ring-twisted analogues, providing an excellent basis for exploring the effects of charge localization on polaron formation. Here, we investigated alkali-metal n -doping of the ladder-type conjugated polymer (polybenzimidazobenzophe-nanthroline) (BBL) through detailed in situ spectroscopic and electrical characterizations. Photoelectron spectroscopy and ultraviolet-visible-near-infrared (UV-vis-NIR) spectroscopy indicate polaron formation upon potassium (K) doping, which agrees well with theoretical predictions. The semiladder BBB displays a similar evolution in the valence band with the appearance of two new features below the Fermi level upon K-doping. Compared to BBL, distinct differences appear in the UV-vis-NIR spectra due to more localized polaronic states in BBB. The high conductivity (2 S cm(-1)) and low activation energy (44 meV) measured for K-doped BBL suggest disorder-free polaron transport. An even higher conductivity (37 S cm(-1)) is obtained by changing the dopant from K to lithium (Li). We attribute the enhanced conductivity to a decreased perturbation of the polymer nanostructure induced by the smaller Li ions. These results highlight the importance of polymer chain planarity and dopant size for the polaronic state in conjugated polymers.

Organic electrochemical transistors (OECTs) hold promise for developing a variety of high-performance (bio-)electronic devices/circuits. While OECTs based on p-type semiconductors have achieved tremendous progress in recent years, n-type OECTs still suffer from low performance, hampering the development of power-efficient electronics. Here, it is demonstrated that fine-tuning the molecular weight of the rigid, ladder-type n-type polymer poly(benzimidazobenzophenanthroline) (BBL) by only one order of magnitude (from 4.9 to 51 kDa) enables the development of n-type OECTs with record-high geometry-normalized transconductance (g(m,norm) approximate to 11 S cm(-1)) and electron mobility x volumetric capacitance (mu C* approximate to 26 F cm(-1) V-1 s(-1)), fast temporal response (0.38 ms), and low threshold voltage (0.15 V). This enhancement in OECT performance is ascribed to a more efficient intermolecular charge transport in high-molecular-weight BBL than in the low-molecular-weight counterpart. OECT-based complementary inverters are also demonstrated with record-high voltage gains of up to 100 V V-1 and ultralow power consumption down to 0.32 nW, depending on the supply voltage. These devices are among the best sub-1 V complementary inverters reported to date. These findings demonstrate the importance of molecular weight in optimizing the OECT performance of rigid organic mixed ionic-electronic conductors and open for a new generation of power-efficient organic (bio-)electronic devices.

Three lactone-based rigid semiconducting polymers were designed to overcome major limitations in the development of n-type organic thermoelectrics, namely electrical conductivity and air stability. Experimental and theoretical investigations demonstrated that increasing the lactone group density by increasing the benzene content from 0 % benzene (P-0), to 50 % (P-50), and 75 % (P-75) resulted in progressively larger electron affinities (up to 4.37 eV), suggesting a more favorable doping process, when employing (N-DMBI) as the dopant. Larger polaron delocalization was also evident, due to the more planarized conformation, which is proposed to lead to a lower hopping energy barrier. As a consequence, the electrical conductivity increased by three orders of magnitude, to achieve values of up to 12 S cm and Power factors of 13.2 mu Wm(-1) K-2 were thereby enabled. These findings present new insights into material design guidelines for the future development of air stable n-type organic thermoelectrics.

The ability to accurately extract low-amplitude voltage signals is crucial in several fields, ranging from single-use diagnostics and medical technology to robotics and the Internet of Things (IoT). The organic electrochemical transistor (OECT), which features large transconductance values at low operating voltages, is ideal for monitoring small signals. Here, low-power and high-gain flexible circuits based on printed complementary OECTs are reported. This work leverages the low threshold voltage of both p-type and n-type enhancement-mode OECTs to develop complementary voltage amplifiers that can sense voltages as low as 100 mu V, with gains of 30.4 dB and at a power consumption of 0.1-2.7 mu W (single-stage amplifier). At the optimal operating conditions, the voltage gain normalized to power consumption reaches 169 dB mu W-1, which is >50 times larger than state-of-the-art OECT-based amplifiers. In a monolithically integrated two-stage configuration, these complementary voltage amplifiers reach voltage gains of 193 V/V, which are among the highest for emerging complementary metal-oxide-semiconductor-like technologies operating at supply voltages below 1 V. These flexible complementary circuits based on printed OECTs define a new power-efficient platform for sensing and amplifying low-amplitude voltage signals in several emerging beyond-silicon applications.

Energy level alignment (ELA) at donor-acceptor heterojunctions is of vital importance yet largely undetermined in organic solar cells. Here, authors determine the heterojunction ELA with (mono) layer-by-layer precision to understand the co-existence of efficient charge. Energy level alignment (ELA) at donor (D) -acceptor (A) heterojunctions is essential for understanding the charge generation and recombination process in organic photovoltaic devices. However, the ELA at the D-A interfaces is largely underdetermined, resulting in debates on the fundamental operating mechanisms of high-efficiency non-fullerene organic solar cells. Here, we systematically investigate ELA and its depth-dependent variation of a range of donor/non-fullerene-acceptor interfaces by fabricating and characterizing D-A quasi bilayers and planar bilayers. In contrast to previous assumptions, we observe significant vacuum level (VL) shifts existing at the D-A interfaces, which are demonstrated to be abrupt, extending over only 1-2 layers at the heterojunctions, and are attributed to interface dipoles induced by D-A electrostatic potential differences. The VL shifts result in reduced interfacial energetic offsets and increased charge transfer (CT) state energies which reconcile the conflicting observations of large energy level offsets inferred from neat films and large CT energies of donor - non-fullerene-acceptor systems.

Introduction of filler materials into organic solar cells (OSCs) are a promising strategy to improve device performance and thermal/mechanical stability. However, the complex interactions between the state-of-the-art OSC materials and filler require careful selection of filler materials and OSC fabrication to achieve lower cost and improved performance. In this work, the introduction of a natural product betulin-based insulating polymer as filler in various OSCs is investigated. Donor-acceptor-insulator ternary OSCs are developed with improved open-circuit voltage due to decreased trap-assisted recombination. Furthermore, filler-induced vertical phase separation due to mismatched surface energy can strongly affect charge collection at the bottom interface and limit the filler ratio. A quasi-bilayer strategy is used in all-polymer systems to circumvent this problem. Herein, the variety of filler materials in OSCs to biomass is broadened, and the filler strategy is made a feasible and promising strategy toward highly efficient, eco, and low-cost OSCs.

A common way of determining the majority charge carriers of pristine and doped semiconducting polymers is to measure the sign of the Seebeck coefficient. However, a polarity change of the Seebeck coefficient has recently been observed to occur in highly doped polymers. Here, it is shown that the Seebeck coefficient inversion is the result of the density of states filling and opening of a hard Coulomb gap around the Fermi energy at high doping levels. Electrochemical n-doping is used to induce high carrier density (>1 charge/monomer) in the model system poly(benzimidazobenzophenanthroline) (BBL). By combining conductivity and Seebeck coefficient measurements with in situ electron paramagnetic resonance, UV-vis-NIR, Raman spectroelectrochemistry, density functional theory calculations, and kinetic Monte Carlo simulations, the formation of multiply charged species and the opening of a hard Coulomb gap in the density of states, which is responsible for the Seebeck coefficient inversion and drop in electrical conductivity, are uncovered. The findings provide a simple picture that clarifies the roles of energetic disorder and Coulomb interactions in highly doped polymers and have implications for the molecular design of next-generation conjugated polymers.

Future brain-machine interfaces, prosthetics, and intelligent soft robotics will require integrating artificial neuromorphic devices with biological systems. Due to their poor biocompatibility, circuit complexity, low energy efficiency, and operating principles fundamentally different from the ion signal modulation of biology, traditional Silicon-based neuromorphic implementations have limited bio-integration potential. Here, we report the first organic electrochemical neurons (OECNs) with ion-modulated spiking, based on all-printed complementary organic electrochemical transistors. We demonstrate facile bio-integration of OECNs with Venus Flytrap (Dionaea muscipula) to induce lobe closure upon input stimuli. The OECNs can also be integrated with all-printed organic electrochemical synapses (OECSs), exhibiting short-term plasticity with paired-pulse facilitation and long-term plasticity with retention >1000 s, facilitating Hebbian learning. These soft and flexible OECNs operate below 0.6 V and respond to multiple stimuli, defining a new vista for localized artificial neuronal systems possible to integrate with bio-signaling systems of plants, invertebrates, and vertebrates. The integration of artificial neuromorphic devices with biological systems plays a fundamental role for future brain-machine interfaces, prosthetics, and intelligent soft robotics. Harikesh et al. demonstrate all-printed organic electrochemical neurons on Venus flytrap that is controlled to open and close.

Acceptor copolymers with low lowest unoccupied molecular orbital (LUMO) energy levels are key materials for organic electronics. In the present work, quaternization of pyridine -flanked diketopyrrolopyrrole (PyDPPPy) is used to lower the LUMO energy level of the resulting monomer (MePyDPPPy) by as much as 0.7 eV. The drastically changed electronic properties of MePyDPPPy hinder a second methylation step even in an excess of trimethyloxonium tetrafluoroborate and thereby give access to the asymmetric functionalization of N-heterocycle -flanked DPP building blocks. The corresponding n-type polymeric ionene PMePyDPPPyT2 with bithiophene as comonomer forms thixotropic organogels with the p-type polythiophene P(g(4)2T-TT), indicative of specific cross-interactions between this couple of copolymers. Gelation of polymer blend solutions, which is absent for other couples of p-type/ n-type polymers, is of general interest for (co)processing and orientation of different electronic polymers simultaneously into films or filaments. Detailed optical and electronic characterization reveals that films processed from organogels exhibit ground-state electron transfer (GSET) enabled by suitably positioned highest occupied molecular orbital (HOMO) and LUMO energy levels of P(g(4)2T-TT) (-4.07 eV) and PMePyDPPPyT2 (-4.20 eV), respectively. Furthermore, molecular interactions related to gelation and GSET do not appear to significantly influence the morphology of the polymer blend films.

Layered metal-organic frameworks attract interests for optoelectronics and spintronics. Here, the authors report a strategy to tune interlayer charge transport and thermoelectric properties via side-chain induced control of the layer spacing. Two-dimensional conjugated metal-organic frameworks (2D c-MOFs) have attracted increasing interests for (opto)-electronics and spintronics. They generally consist of van der Waals stacked layers and exhibit layer-depended electronic properties. While considerable efforts have been made to regulate the charge transport within a layer, precise control of electronic coupling between layers has not yet been achieved. Herein, we report a strategy to precisely tune interlayer charge transport in 2D c-MOFs via side-chain induced control of the layer spacing. We design hexaiminotriindole ligands allowing programmed functionalization with tailored alkyl chains (HATI_CX, X = 1,3,4; X refers to the carbon numbers of the alkyl chains) for the synthesis of semiconducting Ni-3(HATI_CX)(2). The layer spacing of these MOFs can be precisely varied from 3.40 to 3.70 angstrom, leading to widened band gap, suppressed carrier mobilities, and significant improvement of the Seebeck coefficient. With this demonstration, we further achieve a record-high thermoelectric power factor of 68 +/- 3 nW m(-1) K-2 in Ni-3(HATI_C3)(2), superior to the reported holes-dominated MOFs.

Organic electrochemical transistors formed by in operando electropolymerization of the semiconducting channel are increasingly becoming recognized as a simple and effective implementation of synapses in neuromorphic hardware. However, very few studies have reported the requirements that must be met to ensure that the polymer spreads along the substrate to form a functional conducting channel. The nature of the interface between the substrate and various monomer precursors of conducting polymers through molecular dynamics simulations is investigated, showing that monomer adsorption to the substrate produces an increase in the effective monomer concentration at the surface. By evaluating combinatorial couples of monomers baring various sidechains with differently functionalized substrates, it is shown that the interactions between the substrate and the monomer precursor control the lateral growth of a polymer film along an inert substrate. This effect has implications for fabricating synaptic systems on inexpensive, flexible substrates.

Organic electrochemical transistors (OECTs) have the potential to revolutionize the field of organic bioelectronics. To date, most of the reported OECTs include p-type (semi-)conducting polymers as the channel material, while n-type OECTs are yet at an early stage of development, with the best performing electron-transporting materials still suffering from low transconductance, low electron mobility, and slow response time. Here, the high electrical conductivity of multi-walled carbon nanotubes (MWCNTs) and the large volumetric capacitance of the ladder-type pi-conjugated redox polymer poly(benzimidazobenzophenanthroline) (BBL) are leveraged to develop n-type OECTs with record-high performance. It is demonstrated that the use of MWCNTs enhances the electron mobility by more than one order of magnitude, yielding fast transistor transient response (down to 15 ms) and high mu C* (electron mobility x volumetric capacitance) of about 1 F cm(-1) V-1 s(-1). This enables the development of complementary inverters with a voltage gain of >16 and a large worst-case noise margin at a supply voltage of <0.6 V, while consuming less than 1 mu W of power.

A series of fully fused n-type mixed conduction lactam polymers p(g(7)NC(n)N), systematically increasing the alkyl side chain content, are synthesized via an inexpensive, nontoxic, precious-metal-free aldol polycondensation. Employing these polymers as channel materials in organic electrochemical transistors (OECTs) affords state-of-the-art n-type performance with p(g(7)NC(10)N) recording an OECT electron mobility of 1.20 x 10(-2) cm(2) V-1 s(-1) and a mu C* figure of merit of 1.83 F cm(-1) V-1 s(-1). In parallel to high OECT performance, upon solution doping with (4-(1,3-dimethyl-2,3-dihydro-1H-benzoimidazol-2-yl)phenyl)dimethylamine (N-DMBI), the highest thermoelectric performance is observed for p(g(7)NC(4)N), with a maximum electrical conductivity of 7.67 S cm(-1) and a power factor of 10.4 mu Wm(-1) K-2. These results are among the highest reported for n-type polymers. Importantly, while this series of fused polylactam organic mixed ionic-electronic conductors (OMIECs) highlights that synthetic molecular design strategies to bolster OECT performance can be translated to also achieve high organic thermoelectric (OTE) performance, a nuanced synthetic approach must be used to optimize performance. Herein, we outline the performance metrics and provide new insights into the molecular design guidelines for the next generation of high-performance n-type materials for mixed conduction applications, presenting for the first time the results of a single polymer series within both OECT and OTE applications.

n-Type semiconducting polymers with high thermoelectric performance remain challenging due to the scarcity of molecular design strategy, limiting their applications in organic thermoelectric (OTE) devices. Herein, we provide a new approach to enhance the OTE performance of n-doped polymers by introducing acceptor-acceptor (A-A) type backbone bearing branched ethylene glycol (EG) side chains. When doped with 4-(2,3-dihydro-1,3-dimethyl-1H-benzimidazol-2-yl)-N,N-dimethylbenzenamine (N-DMBI), the A-A homopolymer PDTzTI-TEG exhibits n-type electrical conductivity (sigma) up to 34 S cm(-1) and power factor value of 15.7 mu W m(-1) K-2. The OTE performance of PDTzTI-TEG is far greater than that of homopolymer PBTI-TEG (sigma=0.27 S cm(-1)), indicating that introducing electron-deficient thiazole units in the backbone further improves the n-doping efficiency. These results demonstrate that developing A-A type polymers with EG side chains is an effective strategy to enhance n-type OTE performance.

Biomimicry at the hardware level is expected to overcome at least some of the challenges, including high power consumption, large footprint, two-dimensionality, and limited functionality, which arise as the field of artificial intelligence matures. One of the main attributes that allow biological systems to thrive is the successful interpretation of and response to environmental signals. Taking inspiration from these systems, the first demonstration of using multiple environmental inputs to trigger the formation and control the growth of an evolvable synaptic transistor is reported here. The resulting transistor exhibits long-term changes in the channel conductance at a fixed gate voltage. Biomimetic logic circuits are investigated based on this evolvable transistor that implement temperature and pressure inputs to achieve higher order processes like self-regulation of synaptic strength and coincidence detection.

Conducting polymers, such as the p-doped poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS), have enabled the development of an array of opto- and bio-electronics devices. However, to make these technologies truly pervasive, stable and easily processable, n-doped conducting polymers are also needed. Despite major efforts, no n-type equivalents to the benchmark PEDOT:PSS exist to date. Here, we report on the development of poly(benzimidazobenzophenanthroline):poly(ethyleneimine) (BBL:PEI) as an ethanol-based n-type conductive ink. BBL:PEI thin films yield an n-type electrical conductivity reaching 8Scm(-1), along with excellent thermal, ambient, and solvent stability. This printable n-type mixed ion-electron conductor has several technological implications for realizing high-performance organic electronic devices, as demonstrated for organic thermoelectric generators with record high power output and n-type organic electrochemical transistors with a unique depletion mode of operation. BBL:PEI inks hold promise for the development of next-generation bioelectronics and wearable devices, in particular targeting novel functionality, efficiency, and power performance. The development of n-type conductive polymer inks is critical for the development of next-generation opto-electronic devices that rely on efficient hole and electron transport. Here, the authors report an alcohol-based, high performance and stable n-type conductive ink for printed electronics.

Three n-type fused lactam semiconducting polymers were synthesized for thermoelectric and transistor applications via a cheap, highly atom-efficient, and nontoxic transition-metal free aldol polycondensation. Energy level analysis of the three polymers demonstrated that reducing the central acene core size from two anthracenes (A-A), to mixed naphthalene-anthracene (A-N), and two naphthalene cores (N-N) resulted in progressively larger electron affinities, thereby suggesting an increasingly more favorable and efficient solution doping process when employing 4-(2,3-dihydro-1,3-dimethyl-1H-benzimidazol-2-yl)-N,N-dimethylbenzenamine (N-DMBI) as the dopant. Meanwhile, organic field effect transistor (OFET) mobility data showed the N-N and A-N polymers to feature the highest charge carrier mobilities, further highlighting the benefits of aryl core contraction to the electronic performance of the materials. Ultimately, the combination of these two factors resulted in N-N, A-N, and A-A to display power factors (PFs) of 3.2 mu W m(-1) K-2, 1.6 mu W m(-1 )K(-2), and 0.3 mu W m(-1) K-2, respectively, when doped with N-DMBI, whereby the PFs recorded for N-N and A-N are among the highest reported in the literature for n-type polymers. Importantly, the results reported in this study highlight that modulating the size of the central acene ring is a highly effective molecular design strategy to optimize the thermoelectric performance of conjugated polymers, thus also providing new insights into the molecular design guidelines for the next generation of high-performance n-type materials for thermoelectric applications.

There is no molecular strategy for selectively increasing the Seebeck coefficient without reducing the electrical conductivity for organic thermoelectrics. Here, it is reported that the use of amphipathic side chains in an n-type donor-acceptor copolymer can selectively increase the Seebeck coefficient and thus increase the power factor by a factor of approximate to 5. The amphipathic side chain contains an alkyl chain segment as a spacer between the polymer backbone and an ethylene glycol type chain segment. The use of this alkyl spacer does not only reduce the energetic disorder in the conjugated polymer film but can also properly control the dopant sites away from the backbone, which minimizes the adverse influence of counterions. As confirmed by kinetic Monte Carlo simulations with the host-dopant distance as the only variable, a reduced Coulombic interaction resulting from a larger host-dopant distance contributes to a higher Seebeck coefficient for a given electrical conductivity. Finally, an optimized power factor of 18 mu W m(-1) K-2 is achieved in the doped polymer film. This work provides a facile molecular strategy for selectively improving the Seebeck coefficient and opens up a new route for optimizing the dopant location toward realizing better n-type polymeric thermoelectrics.

The limited ionic conductivity is the main issue for the application of solid-state ionic conductors. In this work, we have shown that increasing the ferroelectric phase content in a polymer matrix could enhance the molar ionic conductivity of the incorporated ionic liquid by two orders of magnitude compared to the original films with the same composition. The ferroelectric polymer fiber mats were prepared through electrospinning to induce the ferroelectric phase that ensure the polarization of the dipoles. After analyzing the ferroelectric phase content and polarization of the fiber mats and films containing different ion concentration with FTIR spectroscopy and piezoelectric characterization, a detailed mechanism explaining the improved conductivity in the ferroelectric fiber mats was proposed. Benefiting from the good flexibility, improved ionic conductivity and high temperature coefficient of the fiber mats, we fabricated an organic ionic thermistor. The temperature tracking and mapping function of the ionic thermistor was demonstrated by using two devices with 4 and 16 pixels.

The development of n-type organic electrochemical transistors (OECTs) lags far behind their p-type counterparts. In order to address this dilemma, we report here two new fused bithiophene imide dimer (f-BTI2)-based n-type polymers with a branched methyl end-capped glycol side chain, which exhibit good solubility, low-lying LUMO energy levels, favorable polymer chain orientation, and efficient ion transport property, thus yielding a remarkable OECT electron mobility (mu(e)) of up to approximate to 10(-2) cm(2) V-1 s(-1) and volumetric capacitance (C*) as high as 443 F cm(-3), simultaneously. As a result, the f-BTI2TEG-FT-based OECTs deliver a record-high maximum geometry-normalized transconductance of 4.60 S cm(-1) and a maximum mu C* product of 15.2 F cm(-1) V-1 s(-1). The mu C* figure of merit is more than one order of magnitude higher than that of the state-of-the-art n-type OECTs. The emergence of f-BTI2TEG-FT brings a new paradigm for developing high-performance n-type polymers for low-power OECT applications.

Polymeric mixed ionic-electronic conductors (MIECs) combine aspects of conjugated polymers, polymer electrolytes, and polyelectrolytes to simultaneously transport and couple ionic and electronic charges, opening exciting new applications in energy storage and conversion, bioelectronics, and display technologies. The many applications of polymeric MIECs lead to a wide range of transport conditions. Ionic and electronic transport are directly coupled through electrochemical doping, while the mechanisms of ionic and electronic transport depend on distinctly different chemical functionality, (macro)molecular structure, and morphology. Despite this, ionic and electronic transport are surprisingly tunable, independent of one another. We review the various types of polymeric MIECs, the mechanisms of ionic and electronic charge transport across conditions, and the interrelations between the two, with special emphasis on the unique aspects of polymeric MIEC transport phenomena.

The oxygen reduction reaction (ORR) limits the efficiency of oxygen-associated energy conversion in fuel cells and air-metal batteries. Today, expensive noble metal catalysts are often utilized to enhance the ORR and the resulting conversion efficiency in those devices. Hence, there is an intensive research to find efficient electrodes, exhibiting a favorable electronic structure, for ORR based on abundant materials that can be manufactured using low cost processes. In that context, metal-free carbon-based nanostructures and conducting polymers have been actively investigated. The negatively doped poly(benzimidazobenzophenanthroline) (BBL) as an efficient and stable oxygen cathode material is reported here. Compared to the benchmark p-doped conducting polymer poly(3,4-ethylendioxythiophene) (PEDOT), the BBL provides electrocatalysis that fully reduces dioxygen into water, via a (2 + 2)-electron transfer pathway with hydrogen peroxide (H2O2) as an intermediate; while PEDOT limits the ORR to H2O2. It is demonstrated that n-doped BBL is a promising air electrode material for low-cost and ecofriendly model fuel cells, without the need of any co-catalysts, and its performance is found to be superior to p-doped PEDOT air electrodes.

The synthesis and experimental/theoretical characterization of a new series of electron-transporting copolymers based on the naphthalene bis(4,8-diamino-1,5-dicarboxyl)amide (NBA) building block are reported. Comonomers are designed to test the emergent effects of manipulating backbone torsional characteristics, and density functional theory (DFT) analysis reveals the key role of backbone conformation in optimizing electronic delocalization and transport. The NBA copolymer conformational and electronic properties are characterized using a broad array of molecular/macromolecular, thermal, optical, electrochemical, and charge transport techniques. All NBA copolymers exhibit strongly aggregated morphologies with significant nanoscale order. Copolymer charge transport properties are investigated in thin-film transistors and exhibit excellent electron mobilities ranging from 0.4 to 4.5 cm(2) V-1 s(-1). Importantly, the electron transport efficiency correlates with the film mesoscale order, which emerges from comonomer-dependent backbone planarity and extension. These results illuminate the key NBA building block structure-morphology-bulk property design relationships essential for processable, electronics-applicable high-performance polymeric semiconductors.

Printed thin-film transistors and circuits fabricated on plastic strips can be wrapped around fibres to create stretchable electronics.

Diketopyrrolopyrroles (DPP) have been recognized as a promising acceptor unit for construction of semiconducting donor-acceptor (D-A) polymers, which are typically flanked by spacers such as thiophene rings via a carbon-carbon single bond formation. It may suffer from a decrease in the coplanarity of the molecules especially when bulky side chains are installed. In this work, the two N atoms in the DPP unit are further fused with C-3 of the two flanking thiophene rings, yielding a p-expanded, very planar fused-ring building block (DPPFu). A novel DPPFu-based D-A copolymer (PBDTT-DPPFu) was successfully synthesized, consisting of a benzo[1,2-b:4,5-b]dithiophene (BDTT) unit as a donor and a DPPFu unit as an acceptor. For comparison, the unfused DPP-based counterpart PBDTT-DPP was also synthesized. Two dodecyl alkyl chains were attached to thiophene rings of DPP moieties to ensure good solubility of the DPPFu-based polymer. The influence of the ring-fusion effect on their structure, photophysical properties, electronic properties, molecular packing, and charge transport properties is investigated. Ring-fusion enhances the intermolecular interactions of PBDTT-DPPFu polymer chains as indicated by density functional theory calculation and analysis of electrostatic potential and van der Waals potential and results in significantly improved molecular packing for both the in-plane and out-of-plane directions as suggested by X-ray measurements. Finally, we correlate the molecular packing to the device performance by fabricating field-effect transistors based on these two polymers. The charge carrier mobility of the ring-fused polymer PBDTT-DPPFu is significantly higher as compared to the PBDTT-DPP polymer without ring-fusion, although PBDTT-DPPFu exhibited a much lower number-average molecular weight of 17 kDa as compared to PBDTT-DPP with a molecular weight of 108 kDa. The results from our comparative study provide a robust way to increase the interchain interaction by ring-fusion-promoted coplanarity.

Electron doping of organic semiconductors is typically inefficient, but here a precursor molecular dopant is used to deliver higher n-doping efficiency in a much shorter doping time. Chemical doping is a key process for investigating charge transport in organic semiconductors and improving certain (opto)electronic devices(1-9). N(electron)-doping is fundamentally more challenging than p(hole)-doping and typically achieves a very low doping efficiency (eta) of less than 10%(1,10). An efficient molecular n-dopant should simultaneously exhibit a high reducing power and air stability for broad applicability(1,5,6,9,11), which is very challenging. Here we show a general concept of catalysed n-doping of organic semiconductors using air-stable precursor-type molecular dopants. Incorporation of a transition metal (for example, Pt, Au, Pd) as vapour-deposited nanoparticles or solution-processable organometallic complexes (for example, Pd-2(dba)(3)) catalyses the reaction, as assessed by experimental and theoretical evidence, enabling greatly increased eta in a much shorter doping time and high electrical conductivities (above 100 S cm(-1); ref. (12)). This methodology has technological implications for realizing improved semiconductor devices and offers a broad exploration space of ternary systems comprising catalysts, molecular dopants and semiconductors, thus opening new opportunities in n-doping research and applications(12, 13).

Heat is an abundant but often wasted source of energy. Thus, harvesting just a portion of this tremendous amount of energy holds significant promise for a more sustainable society. While traditional solid-state inorganic semiconductors have dominated the research stage on thermal-to-electrical energy conversion, carbon-based semiconductors have recently attracted a great deal of attention as potential thermoelectric materials for low-temperature energy harvesting, primarily driven by the high abundance of their atomic elements, ease of processing/manufacturing, and intrinsically low thermal conductivity. This quest for new materials has resulted in the discovery of several new kinds of thermoelectric materials and concepts capable of converting a heat flux into an electrical current by means of various types of particles transporting the electric charge: (i) electrons, (ii) ions, and (iii) redox molecules. This has contributed to expanding the applications envisaged for thermoelectric materials far beyond simple conversion of heat into electricity. This is the motivation behind this review. This work is divided in three sections. In the first section, we present the basic principle of the thermoelectric effects when the particles transporting the electric charge are electrons, ions, and redox molecules and describe the conceptual differences between the three thermodiffusion phenomena. In the second section, we review the efforts made on developing devices exploiting these three effects and give a thorough understanding of what limits their performance. In the third section, we review the state-of-the-art thermoelectric materials investigated so far and provide a comprehensive understanding of what limits charge and energy transport in each of these classes of materials.

The emergence of artificial intelligence and the Internet of Things has led to a growing demand for wearable and maintenance-free power sources. The continual push toward lower operating voltages and power consumption in modern integrated circuits has made the development of devices powered by body heat finally feasible. In this context, thermoelectric (TE) materials have emerged as promising candidates for the effective conversion of body heat into electricity to power wearable devices without being limited by environmental conditions. Driven by rapid advances in processing technology and the performance of TE materials over the past two decades, wearable thermoelectric generators (WTEGs) have gradually become more flexible and stretchable so that they can be used on complex and dynamic surfaces. In this review, the functional materials, processing techniques, and strategies for the device design of different types of WTEGs are comprehensively covered. Wearable self-powered systems based on WTEGs are summarized, including multi-function TE modules, hybrid energy harvesting, and all-in-one energy devices. Challenges in organic TE materials, interfacial engineering, and assessments of device performance are discussed, and suggestions for future developments in the area are provided. This review will promote the rapid implementation of wearable TE materials and devices in self-powered electronic systems.

Although there have been many attempts to replace conventional inorganic electronics with organic materials that can be mass produced at low cost, few organic electronic filters to increase immunity to electrical noise have been reported thus far. Conventional Schmitt triggers or their inverters are used in many electronic circuits as versatile electronic noise filters. However, it is challenging to manufacture organic electronic systems with complex circuitry. In this study, a simple, all-solid-state organic Schmitt trigger consisting of twin two-in-one organic ferroelectric memory transistors with the same chemical compositions and device dimensions but different threshold voltages is introduced. Threshold voltages and hysteresis in the two-in-one devices can be controlled by polarization switching as demonstrated in a previous study. Hysteresis of a ferroelectric p-type depletion load inverter can be achieved using twin two-in-one devices when the sweep voltage is higher than the critical gate voltages. This facilitates inverter characteristics at two different threshold voltages, and realizing a Schmitt trigger. Finally, based on simulation program with integrated circuit emphasis (SPICE) simulation, guidelines are proposed on how to design organic Schmitt triggers with p- or n-type materials and ferroelectric or charge-trapping mechanisms to achieve inverting or non-inverting characteristics.

Seawater desalination and wastewater purification technologies are the main strategies against the global fresh water shortage. Among these technologies, solar-driven evaporation is effective in extracting fresh water by efficiently exploiting solar energy. However, building a sustainable and low-cost solar steam generator with high conversion efficiency is still a challenge. Here, pure organic aerogels comprising a cellulose scaffold decorated with an organic conducting polymer absorbing in the infrared are employed to establish a high performance solar steam generator. The low density of the aerogel ensures minimal material requirements, while simultaneously satisfying efficient water transport. To localize the absorbed solar energy and make the system floatable, a porous floating and thermal-insulating foam is placed between the water and the aerogel. Thanks to the high absorbance of the aerogel and the thermal-localization performance of the foam, the system exhibits a high water evaporation rate of 1.61 kg m(-2) h(-1) at 1 kW m(-2) under 1 sun irradiation, which is higher than most reported solar steam generation devices.

Being able to dynamically shape light at the nanoscale is oneof the ultimate goals in nano-optics1. Resonant light–matterinteraction can be achieved using conventional plasmonicsbased on metal nanostructures, but their tunability is highlylimited due to a fixed permittivity2. Materials with switchablestates and methods for dynamic control of light–matterinteraction at the nanoscale are therefore desired. Here weshow that nanodisks of a conductive polymer can supportlocalized surface plasmon resonances in the near-infraredand function as dynamic nano-optical antennas, with their resonancebehaviour tunable by chemical redox reactions. Theseplasmons originate from the mobile polaronic charge carriersof a poly(3,4-ethylenedioxythiophene:sulfate) (PEDOT:Sulf)polymer network. We demonstrate complete and reversibleswitching of the optical response of the nanoantennasby chemical tuning of their redox state, which modulatesthe material permittivity between plasmonic and dielectricregimes via non-volatile changes in the mobile chargecarrier density. Further research may study different conductivepolymers and nanostructures and explore their usein various applications, such as dynamic meta-optics andreflective displays.

Doping of organic semiconductors is crucial for the operation of organic (opto)electronic and electrochemical devices. Typically, this is achieved by adding heterogeneous dopant molecules to the polymer bulk, often resulting in poor stability and performance due to dopant sublimation or aggregation. In small-molecule donor-acceptor systems, charge transfer can yield high and stable electrical conductivities, an approach not yet explored in all-conjugated polymer systems. Here, we report ground-state electron transfer in all-polymer donor-acceptor heterojunctions. Combining low-ionization-energy polymers with high-electron-affinity counterparts yields conducting interfaces with resistivity values five to six orders of magnitude lower than the separate single-layer polymers. The large decrease in resistivity originates from two parallel quasi-two-dimensional electron and hole distributions reaching a concentration of similar to 10(13) cm(-2). Furthermore, we transfer the concept to three-dimensional bulk heterojunctions, displaying exceptional thermal stability due to the absence of molecular dopants. Our findings hold promise for electro-active composites of potential use in, for example, thermoelectrics and wearable electronics. Doping through spontaneous electron transfer between donor and acceptor polymers is obtained by selecting organic semiconductors with suitable electron affinity and ionization energy, achieving high conductivity in blends and bilayer configuration.

Low-cost, non-toxic, abundant organic thermoelectric materials are currently under investigation for use as potential alternatives for the production of electricity from waste heat. While organic conductors reach electrical conductivities as high as their inorganic counterparts, they suffer from an overall low thermoelectric figure of merit (ZT) due to their small Seebeck coefficient. Moreover, the lack of efficient n-type organic materials still represents a major challenge when trying to fabricate efficient organic thermoelectric modules. Here, a novel strategy is proposed both to increase the Seebeck coefficient and achieve the highest thermoelectric efficiency for n-type organic thermoelectrics to date. An organic mixed ion-electron n-type conductor based on highly crystalline and reduced perylene bisimide is developed. Quasi-frozen ionic carriers yield a large ionic Seebeck coefficient of -3021 mu V K-1, while the electronic carriers dominate the electrical conductivity which is as high as 0.18 S cm(-1)at 60% relative humidity. The overall power factor is remarkably high (165 mu W m(-1)K(-2)), with aZT= 0.23 at room temperature. The resulting single leg thermoelectric generators display a high quasi-constant power output. This work paves the way for the design and development of efficient organic thermoelectrics by the rational control of the mobility of the electronic and ionic carriers.

The potential of the screen printing method for large-scale production of organic electrochemical transistors (OECTs), combining high production yield with low cost, is here demonstrated. Fully screen-printed OECTs of 1mm(2) area, based on poly(3,4-ethylenedioxythiophene) doped with poly(styrensulfonate) (PEDOT:PSS), have been manufactured on flexible polyethylene terephthalate (PET) substrates. The goal of this project effort has been to explore and develop the printing processing to enable high yield and stable transistor parameters, targeting miniaturized digital OECT circuits for large-scale integration (LSI). Of the 760 OECTs manufactured in one batch on a PET sheet, only two devices were found malfunctioning, thus achieving an overall manufacturing yield of 99.7%. A drain current ON/OFF ratio at least equal to 400 was applied as the strict exclusion principle for the yield, motivated by proper operation in LSI circuits. This consistent performance of low-footprint OECTs allows for the integration of PEDOT:PSS-based OECTs into complex logic circuits operating at high stability and accuracy.

Organic phototransistor memory is considered as a promising optoelectronic device owing to its multifunctionality. However, due to the poor reliability of each function and the complexity of the device structure, it is necessary to optimize the thin-film process of functional materials when constructing multiple functions into a single device. Here, we demonstrate a dual-functional device that is both a working memory transistor and a phototransistor by incorporating photochromic spironaphthooxazine molecules into an organic insulating layer. The photochmmic molecules in the polymer matrix not only exhibit nonvolatile charge storage properties similar to nano-floating gates but also feature a reversible electronic band structure upon alternating irradiation with ultraviolet and visible light, which makes the device function as both an electrical memory transistor and a phototransistor. Furthermore, the photoresponsive charge trap layer in the demonstrated device leads to excellent memory performance under both dark and light conditions, which includes a large memory window (-56 V), stable endurance cycles (amp;gt;10(2)), and good retention characteristics (amp;gt;10(4) s). Our findings suggest an alternative strategy to realize organic multifunctional nonvolatile memories.

Organic electrochemical transistors (OECTs) have shown great promise in a variety of applications ranging from digital logic circuits to biosensors and artificial synapses for neuromorphic computing. The working mechanism of OECTs relies on the mixed transport of ionic and electronic charge carriers, extending throughout the bulk of the organic channel. This attribute renders OECTs fundamentally different from conventional field effect transistors and endows them with unique features, including large gate-to-channel capacitance, low operating voltage, and high transconductance. Owing to the complexity of the mixed ion-electron coupling and transport processes, the OECT device physics is sophisticated and yet to be fully unraveled. Here, we give an account of the one- and two-dimensional drift-diffusion models that have been developed to describe the mixed transport of ions and electrons by finite-element methods and identify key device parameters to be tuned for the next developments in the field.

The rational creation of two-component conjugated polymer sys-tems with high levels of phase purity in each component is challenging but crucial for realizing printed soft-matter electronics. Here, we report a mixed-flow microfluidic printing (MFMP) approach for two-component pi-polymer systems that significantly elevates phase purity in bulk-heterojunction solar cells and thin-film transistors. MFMP integrates laminar and extensional flows using a specially microstructured shear blade, designed with fluid flow simulation tools to tune the flow patterns and induce shear, stretch, and pushout effects. This optimizes polymer conformation and semi-conducting blend order as assessed by atomic force microscopy (AFM), transmission electron microscopy (TEM), grazing incidence wide-angle X-ray scattering (GIWAXS), resonant soft X-ray scattering (R-SoXS), photovoltaic response, and field effect mobility. For printed all-polymer (poly[(5,6-difluoro-2-octyl-2H-benzotriazole-4,7-diyl)-2,5-thiophenediyl[4,8-bis[5-(2-hexyldecyl)-2-thienyl]benzo[1,2-b:4,5-b ]dithiophene-2,6-diyl]-2,5-thiophenediyl]) [J51]:(poly{[N,N -bis(2-octyldodecyl) naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5 -(2,2 -bithio-phene)}) [N2200]) solar cells, this approach enhances short-circuit currents and fill factors, with power conversion efficiency increasing from 5.20% for conventional blade coating to 7.80% for MFMP. Moreover, the performance of mixed polymer ambipolar [poly(3-hexylthiophene-2,5-diyl) (P3HT):N2200] and semiconducting:insulat-ing polymer unipolar (N2200:polystyrene) transistors is similarly enhanced, underscoring versatility for two-component pi-polymer systems. Mixed-flow designs offer modalities for achieving high-performance organic optoelectronics via innovative printing methodologies.