Electrocatalysis enables the industrial transition to sustainable production of chemicals using abundant precursors and electricity from renewable sources. De-centralized production of hydrogen peroxide (H2O2) from water and oxygen of air is highly desirable for daily life and industry. We report an effective electrochemical refinery (e-refinery) for H2O2 by means of electrocatalysis-controlled comproportionation reaction (2(H)O + O -> 2(HO)), feeding pure water and oxygen only. Mesoporous nickel (II) oxide (NiO) was used as electrocatalyst for oxygen evolution reaction (OER), producing oxygen at the anode. Conducting polymer poly(3,4-ethylenedioxythiophene): poly(styrene sulfonate) (PEDOT:PSS) drove the oxygen reduction reaction (ORR), forming H2O2 on the cathode. The reactions were evaluated in both half-cell and device configurations. The performance of the H2O2 e-refinery, assembled on anion-exchange solid electrolyte and fed with pure water, was limited by the unbalanced ionic transport. Optimization of the operation conditions allowed a conversion efficiency of 80%.

On-site electrosynthesis of hydrogen peroxide (H2O2) is a promising alternative technology to the conversional centralized anthraquinone oxidation process. Here, we report a platinum group metal (PGM)-free H2O2 electrogenerator with mesoporous Cr2O3 and NiCo2O4 used as electrocatalysts for oxygen reduction and evolution reactions (ORR and OER), respectively. The catalysts were synthesized via a hydrothermal synthesis route and had pore sizes of 3 and 7 nm and specific surface areas of 112 and 62 m(2) g(-1), respectively. Mesoporous Cr2O3 was evaluated in a half cell with 0.1 M KOH for electrocatalytic oxygen reduction, which shows 2.2 transferred electrons per oxygen and an in situ H2O2 yield of 70%. This enables the electrosynthesis of hydrogen peroxide in alkaline medium using Cr2O3 as a 2e-ORR-H2O2 electrocatalyst, with oxygen evolution as an auxiliary reaction on NiCo2O4. The effect of electrolyte flow on the H2O2 electrogenerator was investigated. It is observed that one-way feeding of the catholyte suppresses deterioration of the electrocatalyst and allows a faradic conversion up to similar to 90% with a production rate of similar to 0.36 [g (h<middle dot>g(cat))(-1)], operating within the cell voltage of 1.2 V. This work demonstrates both a viable method for electrosynthesis of H2O2 production using PGM-free electrocatalysts and the possibility to obtain a high faradic efficiency by mitigating the effect from catalyst degradation.

The skin is the largest organ of the human body. Wounds disrupt the functions of the skin and can have catastrophic consequences for an individual resulting in significant morbidity and mortality. Wound infections are common and can substantially delay healing and can result in non-healing wounds and sepsis. Early diagnosis and treatment of infection reduce risk of complications and support wound healing. Methods for monitoring of wound pH can facilitate early detection of infection. Here we show a novel strategy for integrating pH sensing capabilities in state-of-the-art hydrogel-based wound dressings fabricated from bacterial nanocellulose (BC). A high surface area material was developed by self-assembly of mesoporous silica nanoparticles (MSNs) in BC. By encapsulating a pH-responsive dye in the MSNs, wound dressings for continuous pH sensing with spatiotemporal resolution were developed. The pH responsive BC-based nanocomposites demonstrated excellent wound dressing properties, with respect to conformability, mechanical properties, and water vapor transmission rate. In addition to facilitating rapid colorimetric assessment of wound pH, this strategy for generating functional BC-MSN nanocomposites can be further be adapted for encapsulation and release of bioactive compounds for treatment of hard-to-heal wounds, enabling development of novel wound care materials.

Lignin, a byproduct from the pulp industry, is one of the redox active biopolymers being investigated as a component in the electrodes for sustainable energy storage applications. Due to its insulating nature, it needs to be combined with a conductor such as carbon or conducting polymer for efficient charge storage. Here, the lignin/carbon composite electrodes manufactured via mechanical milling (ball milling) are reported. The composite formation, correlation between performance and morphology is studied by comparison with manual mixing and jet milling. Superior charge storage capacity with approximate to 70% of the total contribution from the Faradaic process involving the redox functionality of lignin is observed in a mechanically milled composite. In comparison, manual mix shows only approximate to 30% from the lignin storage participation while the rest is due to the electric double layer at the carbon-electrolyte interface. The significant participation of lignin in the ball milled composite is attributed to the homogeneous, intimate mixing of the carbon and the lignin leading the electronic carrier transported in the carbon phase to reach most of the redox group of lignin. A maximum capacity of 49 mAh g(-1) is obtained at charge/discharge rate of 0.25 A g(-1) for the sample milled for 60 min.

Direct electrification of oxygen-associated reactionscontributesto large-scale electrical storage and the launch of the green hydrogeneconomy. The design of the involved catalysts can mitigate the electricalenergy losses and improve the control of the reaction products. Weevaluate the effect of the interface composition of electrocatalystson the efficiency and productivity of the oxygen reduction reaction(ORR) and oxygen evolution reaction (OER), both mechanistically andat device levels. The ORR and OER were benchmarked on mesoporous nickel-(II)oxide and nickel cobaltite (NiO and NiCo2O4,respectively) obtained by a facile template-free hydrothermal synthesis.Physicochemical characterization showed that both NiO and NiCo2O4 are mesoporous and have a cubic crystal structurewith abundant surface hydroxyl species. NiCo2O4 showed higher electrocatalytic activity in OER and selectivity towater as the terminal product of ORR. On the contrary, ORR over NiOyielded hydroxyl radicals as products of a Fenton-like reaction ofH(2)O(2). The product selectivity in ORR was usedto construct two electrolyzers for electrified purification of oxygenand generation of hydroxyl radicals.

Zn-ion batteries are one of the hot candidates for low-cost and sustainable secondary batteries. The hydrogen evolution and dendritic growth upon zinc deposition are todays challenges for that technology. One of the new strategies to cope with these issues is to use "water-in-salt" electrolyte (WISE), that is, super concentrated aqueous electrolytes, to broaden its electrochemical stability window (ESW), suppressing hydrogen evolution reaction (HER), and perturbing the dendritic growth. Herein, this work proposes to use "water-in-polymer salt" electrolyte (WIPSE) concept to mitigate the challenges with Zn ion batteries and bring this technology toward one of the cheapest, greenest, and most sustainable electrodes: Lignin-carbon (L-C) electrode. Potassium polyacrylate (PAAK) as WISE bears out as better electrolyte for L-C electrodes in terms of self-discharge, cyclic stability, and specific capacity compared to conventional electrolyte based on chemically cousin molecule potassium acetate. Zinc bis(trifluoromethanesulfonyl) imide (Zn(TFSI)(2)) added into WIPSE shows deposition and dissolution of Zn in Zn//Zn symmetric cell suggesting that Zn2+ are moving into the polyanionic network. Furthermore, the added bis (trifluor omethanesul fonyl) imide (TFSI-) metal salts trigger a approximate to 40% enhancement of the capacity of L-C electrode. These results show a new promising direction toward the development of cost-effective and sustainable Zn-lignin batteries.

Bifunctional electrocatalysts with both accelerated oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) enable high-power density electricity storage and decentralized extraction of pure oxygen from air for usage in health care. Herein, a hydrothermal synthesis employing the anionic surfactant sodium dodecyl sulfate as structure-directing agent is developed to fabricate a family of crystalline mesoporous metal oxides (meso-MO X , M = Cr, Fe, Co, Ni, Ce). The pore size and specific surface area depend on the metal used and they range from 3 to 6 nm and 60 to 200 m(2) g(-1), respectively. NiO and Co3O4 show a higher catalytic efficiency in alkaline media in comparison with the other oxides studied, and their activities are comparable with the values reported for platinum group metal (PGM)-based electrocatalysts. This stems from lower voltage losses and by the presence of specific hydroxide adsorbates on the surface. Both ORR and OER driven on Co3O4 show the unified rate-determining chemical step (|OO-|(center dot) (ads) + H2O <-> |OOH|(center dot) (ads) + OH-, where | X | ads are the species adsorbed on active sites). The bifunctional ORR/OER electrocatalysis obtained on mesoporous NiO is utilized for the first symmetrical PGM-free oxygen pump fed by air and water only.

A green, though black, sustainable and low-cost carbon material-charcoal produced from wood-is developed for electricity storage. Charcoal electrodes are fabricated by ball-milling charcoal and adding protein nanofibril binders. The charcoal electrode presents a capacitance of 360 F g(-1) and a conductivity of 0.2 S m(-1). A pair of redox peaks is observed in the cyclic voltammetry and assigned to originate from quinone groups. Compared with other wooden electrodes, these charcoal electrodes display better cycling stability with 88% capacity retention after 1000 cycles. Their discharge capacity is 2.5 times that of lignosulfonate/graphite hybrid electrodes.

Corrosion resistance and catalytic activity toward the oxygen reduction reaction (ORR) in an alkaline environment are two key properties for water recombination applications. In this work, CoCrFexNi (0 <= x <= 0.7) thin films were deposited by magnetron sputtering on polished steel substrates. The native passive layer was 2-4 nm thick and coherent to the columnar grains determined by transmission electron microscopy. The effect of Fe on the corrosion properties in 0.1 M NaCl and 1 M KOH and the catalytic activity of the films toward ORR were investigated. Electrochemical impedance spectroscopy and potentiodynamic polarization measurements indicate that CoCrFe0.7Ni and CoCrFe0.3Ni have the highest corrosion resistance of the studied films in NaCl and KOH, respectively. The high corrosion resistance of the CoCrFe0.7Ni film in NaCl was attributed to the smaller overall grain size, which leads to a more homogeneous film with a stronger passive layer. For CoCrFe0.3Ni in KOH, it was attributed to a lower Fe dissolution into the electrolyte and the build-up of a thick and protective hydroxide layer. Scanning Kelvin probe force microscopy showed no potential differences globally in any of the films, but locally, a potential gradient between the top of the columns and grain boundaries was observed. Corrosion of the films was likely initiated at the top of the columns where the potential was lowest. It was concluded that Fe is essential for the electrochemical activation of the surfaces and the catalytic activity toward ORR in an alkaline medium. The highest catalytic activity was recorded for high Fe-content films (x >= 0.5) and was attributed to the formation of platelet-like oxide particles on the film surface upon anodization. The study showed that the combination of corrosion resistance and catalytic activity toward ORR is possible for CoCrFexNi, making this material system a suitable candidate for water recombination in an alkaline environment.

In this work, we demonstrate an effective anion capturing in an aqueous medium using a highly porous carbon paper decorated with ZnO nanorods. A sol-gel technique was first employed to form a thin and compact seed layer of ZnO nanoparticles on the dense network of carbon fibers in the carbon paper. Subsequently, ZnO nanorods were successfully grown on the pre-seeded carbon papers using inexpensive chemical bath deposition. The prepared porous electrodes were electrochemically investigated for improved charge storage and stability under long-term operational conditions. The results show effective capacitive deionization with a maximum areal capacitance of 2 mF/cm(2), an energy consumption of 50 kJ per mole of chlorine ions, and an excellent long-term stability of the fabricated C-ZnO electrodes. The experimental results are supported by COMSOL simulations. Besides the demonstrated capacitive desalination application, our results can directly be used to realize suitable electrodes for energy storage in supercapacitors.

Oxygen evolution reaction (OER) is critical for producing high purity hydrogen and oxygen via electrocatalytic water splitting. In this work, single crystalline, nanoporous nickel oxide (NiO) was prepared using a hydro thermal, soft-templated synthesis route followed by calcination at different temperatures. It is shown that the NiO crystals have a cubic lattice, and the pore size can be tuned from similar to 1 to similar to 70 nm by varying the calcination temperature, i.e. variation from micro to macroporosity. The NiOs catalytic performance as electrocatalysts was evaluated in OER, both thermodynamically and kinetically. Mesoporous NiO with calcination temperature of 400 degrees C had the lowest overpotential (335 mV) required @ 10 mA/cm(2) accompanied with the highest turnover frequency value and mass activity among of the obtained NiO electrocatalysts. The study shows that the electrocatalytic activity of nanoporous NiO outperforms that of commercial catalyst Ir/C (similar to 360 mV @ 10 mA/cm(2)). Microporous NiO possess the highest specific surface area and electrical double layer capacitance, while the nonporous NiO particles have the highest specific activity and BET activity of the catalysts. It is concluded that the minimization of voltage losses by the nanoscale enlargement of the electrocatalyst surface area shows the coherence between gas adsorption and electrocapacitive measurements. Conversely, the OER kinetics showed deterioration with surface area maximization due to the impediment of ionic transport inside the micropores. This work demonstrates the importance of morphology optimization to obtain an efficient OER electrocatalyst with low required overpotential and kinetic loss.

Mesoporous silicon (mSi) obtained by the magnesiothermic reduction of mesoporous silica was used to deposit polyaniline (PANI) in its pores, the composite was tested for its charge storage application for high performance supercapacitor electrodes. The mesoporous silica as confirmed by Small Angle X-ray Scattering (SAXS) has a Brunauer-Emmett-Teller (BET) surface area of 724 m(2)g(-1) and mean pore size of 5 nm. After magnesiothermic reduction to mSi, the BET surface area is reduced to 348 m(2)g(-1) but the mesoporousity is retained with a mean pore size of 10 nm. The BET surface area of mesoporous silicon is among the highest for porous silicon prepared/reduced from silica. In situ polymerization of PANI inside the pores of mSi was achieved by controlling the polymerization conditions. As a supercapacitor electrode, the mSi-PANI composite exhibits better charge storage performance as compared to pure PANI and mesoporous silica-PANI composite electrodes. Enhanced electrochemical performance of the mSi-PANI composite is attributed to the high surface mesoporous morphology of mSi with a network structure containing abundant mesopores enwrapped by an electrochemically permeable polyaniline matrix.

Mesoporous silica- and carbon-based materials, including bioactive glasses, have proven potential as components of medical devices and as drug carriers. From an application perspective, knowledge about the shelf-life stability of these materials under various conditions is vital. Here, mesoporous bioactive glasses (MBGs) synthesized by aerosol-assisted spray-drying and by a batch sol-gel method, mesoporous silicas of SBA-15 type, and mesoporous carbons CMK-1 and CMK-3 have been stored under varying conditions, e.g. at different temperature and relative humidity (RH), and in different storage vessels. The results show that the silica-based materials stored in Eppendorfs are sensitive to humidity. Spray dried MBGs decompose within 1 month at a RH >5%, whilst sol-gel MBGs are more stable up to a RH >60%. Changing the storage vessel to sealed glass flasks increases the MBGs lifetime significantly, with no degradation during 2 months of storage at a RH = 75%. SBA-15 stored in Eppendorfs are more stable compared to MBGs, and addition of F- ions added during the synthesis affects the material degradation rate. Mesoporous carbons are stable under all conditions for all time points. This systematic study clearly demonstrates the importance of storage conditions for mesoporous materials which is crucial knowledge for commercialization of these materials. (C) 2021 The Author(s). Published by Elsevier B.V. on behalf of The Korean Society of Industrial and Engineering Chemistry.

Catalysts and electmcatalysts are crucial for energy production and storage. To develop cost-efficient systems taking advantage of functionalized surfaces, the catalysts can be synthesized as nanomaterials or thin films. In this work, cobalt thin films were deposited on low-alloyed steel using magnetron sputtering. The films are uniform with a smooth surface and a thickness of similar to 400 nm. The films were electrochemically oxidized via anodization to a mix of cobalt oxides, one of them being Co3O4, at room temperature in an alkaline solution. The electrocatalytic performances of the anodized films were evaluated in 1 M KOH electrolyte saturated with oxygen. Cathodic currents in -0.5 mA/cm(2) range, corresponding to oxygen reduction reaction (ORR) activity, were measured with cyclic voltammetry. The catalytic activity of the films was evaluated as a function of time. The anodized Co coating exhibited three times higher activity than the steel substrate. The kinetics for the ORR were evaluated through Tafel plots and a slope of 226 mV/decade was found. Post-ORR characterization of the films revealed hexagonal plate-like oxide particles on the surface. After 50 cyclic voltammograms, the film was further oxidized, indicating that the ORR activity also affects the overall surface state of the film. This study demonstrates that thin films, after electrochemical modification, can be electrocatalysts for the oxygen reduction reaction and potentially used for applications in energy production and storage.

Nanocomposites of metal nanoparticles (NPs) and bacterial nanocellulose (BC) enable fabrication of soft and biocompatible materials for optical, catalytic, electronic, and biomedical applications. Current BC-NP nanocomposites are typically prepared by in situ synthesis of the NPs or electrostatic adsorption of surface functionalized NPs, which limits possibilities to control and tune NP size, shape, concentration, and surface chemistry and influences the properties and performance of the materials. Here a self-assembly strategy is described for fabrication of complex and well-defined BC-NP composites using colloidal gold and silver NPs of different sizes, shapes, and concentrations. The self-assembly process results in nanocomposites with distinct biophysical and optical properties. In addition to antibacterial materials and materials with excellent senor performance, materials with unique mechanoplasmonic properties are developed. The homogenous incorporation of plasmonic gold NPs in the BC enables extensive modulation of the optical properties by mechanical stimuli. Compression gives rise to near-field coupling between adsorbed NPs, resulting in tunable spectral variations and enhanced broadband absorption that amplify both nonlinear optical and thermoplasmonic effects and enables novel biosensing strategies.

Spatially and temporally controlled drug delivery is important for implant and tissue engineering applications, as the efficacy and bioavailability of the drug can be enhanced, and can also allow for drugging stem cells at different stages of development. Long-term drug delivery over weeks to months is however difficult to achieve, and coating of 3D surfaces or creating patterned surfaces is a challenge using coating techniques like spin- and dip-coating. In this study, mesoporous films consisting of SBA-15 particles grown onto silicon wafers using wet processing were evaluated as a scaffold for drug delivery. Films with various particle sizes (100-900 nm) and hence thicknesses were grown onto trichloro(octadecyl)silane-functionalized silicon wafers using a direct growth method. Precise patterning of the areas for film growth could be obtained by local removal of the OTS functionalization through laser ablation. The films were incubated with the drug model 3,3 -dioctadecyloxacarbocyanine perchlorate (DiO), and murine myoblast cells (C2C12 cells) were seeded onto films with different particle sizes. Confocal laser scanning microscopy (CLSM) was used to study the cell growth, and a vinculin-mediated adherence of C2C12 cells on all films was verified. The successful loading of DiO into the films was confirmed by UV-vis and CLSM. It was observed that the drugs did not desorb from the particles during 24 hours in cell culture. During adherent growth on the films for 4 h, small amounts of DiO and separate particles were observed inside single cells. After 24 h, a larger number of particles and a strong DiO signal were recorded in the cells, indicating a particle mediated drug uptake. The vast majority of the DiO-loaded particles remained attached to the substrate also after 24 h of incubation, making the films attractive as longer-term reservoirs for drugs on e.g. medical implants.

We report the formation of mesoporous films consisting of SBA-15 particles grown directly onto substrates and their usage as catalysts in esterification of acetic acid and ethanol. The film thickness was altered between 80 nm and 750 nm by adding NH4F to the synthesis solution. The salt also affects the formation rate of the particles, and substrates must be added during the formation of the siliceous network in the solution. Various substrate functionalizations were tested and hydrophobic substrates are required for a successful film growth. We show that large surfaces (amp;gt; 75 cm(2)), as well as 3D substrates, can be homogenously coated. Further, the films were functionalized, either with acetic acid through co-condensation, or by coating the films with a thin carbon layer through exposure to furfuryl alcohol fumes followed by carbonization and sulfonation with H2SO4. The carbon-coated film was shown to be an efficient catalyst in the esterification reaction with acetic acid and ethanol. Due to the short, accessible mesopores, chemical variability, and possibility to homogenously cover large, rough surfaces. the films have a large potential for usage in various applications such as catalysis, sensing, and drug delivery.

A hybrid catalyst consisting of Zr-doped mesoporous silica (Zr-SBA-15) supports with intergrown Cu nanoparticles was used to study the effects of a catalysts chemical states on CO2 hydrogenation. The chemical state of the catalyst was altered by using tetraethyl orthosilicate (TEOS) or sodium metasilicate (SMS) as the silica precursor in the synthesis of the Zr-SBA-15 framework, and infiltration (Inf) or evaporation induced wetness impregnation (EIWI) as the Cu loading method. As a result, the silica precursor mainly affects the activity of the catalyst whereas the Cu loading method alters the selectivity of the products. TEOS materials exhibit a higher catalytic activity compared to SMS materials due to different Zr dispersion and bonding to the silica matrix. EIWI catalysts display selectivity for methanol formation, while the Inf ones enable methanol conversion to DME. This is correlated to a higher Zr content and lower Cu oxidation states of EIWI prepared catalysts. (C) 2019 Elsevier Inc. All rights reserved.

Trace-level detection of mercury in waters is connected with several complications including complex multistep analysis routines, applying additional, harmful reagents increasing the risk of contamination, and the need for expensive analysis equipment. Here, we present a straightforward reagent-free approach for mercury trace determination using a novel thin film sampling stick for passive sampling based on gold nanoparticles. The nanoparticles supported on a silicon wafer and further covered with a thin layer of mesoporous silica. The mesoporous silica layer is acting as a protection layer preventing gold desorption upon exposure to water. The gold nanoparticles are created by thermal treatment of a homogenous gold layer on silicon wafer prepared by vacuum evaporation. This gold-covered substrate is subsequently covered by a layer of mesoporous silica through dip-coating. Dissolved mercury ions are extracted from a water sample, e.g., river water, by incorporation into the gold matrix in a diffusion-controlled manner. Thus, the amount of mercury accumulated during sampling depends on the mercury concentration of the water sample, the accumulation time, as well as the size of the substrate. Therefore, the experimental conditions can be chosen to fit any given mercury concentration level without loss of sensitivity. Determination of the mercury amount collected on the stick is performed after thermal desorption of mercury in the gas phase using atomic fluorescence spectrometry. Furthermore, the substrates can be re-used several tens of times without any loss of performance, and the batch-to-batch variations are minimal. Therefore, the nanogold-mesoporous silica sampling substrates allow for highly sensitive, simple, and reagent-free determination of mercury trace concentrations in waters, which should also be applicable for on-site analysis. Successful validation of the method was shown by measurement of mercury concentration in the certified reference material ORMS-5, a river water.

In situ attenuated total reflectance Fourier transform infrared spectroscopy is used to monitor the chemical evolution of the mesoporous silica SBA-15 from hydrolysis of the silica precursor to final silica condensation after the particle formation. Two silica precursors, tetraethyl orthosilicate (TEOS) or sodium metasilicate (SMS) were used, and the effects of additive (heptane and NH4F) concentrations were studied. Five formation stages are identified when TEOS is used as the precursor. The fourth stage correlates with the appearance and evolution of diffraction peaks recorded using in situ small angle X-ray diffraction. Details of the formed silica matrix are observed, e.g. the ratio between six-fold cyclic silica rings and linear bonding increases with the NH4F concentration. The TEOS hydrolysis time is independent of the NH4F concentration for small amounts of heptane, but is affected by the size of the emulsion droplets when the heptane amount increases. Polymerization and condensation rates of both silica precursors are affected by the salt concentration. Materials synthesized using SMS form significantly faster compared to TEOS-materials due to the pre-hydrolysis of the precursor. The study provides detailed insights into how the composition of the synthesis solution affects the chemical evolution and micellar aggregation during formation of mesoporous silica. (C) 2018 Elsevier Inc. All rights reserved.

The development of high-performance and transferable thin-film thermoelectric materials is important for low-power applications, e.g., to power wearable electronics, and for on-chip cooling. Nanoporous films offer an opportunity to improve thermoelectric performance by selectively scattering phonons without affecting electronic transport. Here, we report the growth of nanoporous Ca3Co4O9 thin films by a sequential sputtering-annealing method. Ca3Co4O9 is promising for its high Seebeck coefficient and good electrical conductivity and important for its nontoxicity, low cost, and abundance of its constituent raw materials. To grow nanoporous films, multilayered CaO/CoO films were deposited on sapphire and mica substrates by rf-magnetron reactive sputtering from elemental Ca and Co targets, followed by annealing at 700 C to form the final phase of Ca3Co4O9. This phase transformation is accompanied by a volume contraction causing formation of nanopores in the film. The thermoelectric propoperties of the nanoporous Ca3Co4O9 films can be altered by controlling the porosity. The lowest electrical resistivity is ~7 mO cm, yielding a power factor of 2.32 × 10-4 Wm-1K-2 near room temperature. Furthermore, the films are transferable from the primary mica substrates to other arbitrary polymer platforms by simple dry transfer, which opens an opportunity of low-temperature use these materials.

The effects of catalyst matrix porosity composition on the catalytic performance have been studied using sulfonated mesoporous SBA-15 silica. The matrix was sulfonated with three different methods grafting, in situ oxidation, and carbon infiltration. Additionally, unordered sulfonated mesoporous carbon, and the commercial catalysts Amberlite IR-120 and Nafion 117 were tested. The catalytic performance was evaluated in a Fischer esterification using acetic acid and ethanol, as well as in a transesterification of triglycerides (sunflower oil) and ethanol to produce biodiesel. The study shows that for long carbon chains, the effective wetting of the porous catalyst matrix by the reactants is most important for the catalytic efficiency, while for shorter carbon chain, the mass transport of the reagents trough the porous structure is more important. The catalysts were analysed using electron microscopy and physisorption. The study shows that the reactions are faster with carbon infiltrated materials than the silica materials due to a higher concentration of sulfonic groups linked to the carbon. The in situ functionalized SBA-15 is a more efficient catalyst compared to the post grafted one. All the synthesized catalysts outperform the commercial ones in both reactions in terms of conversion. (C) 2017 Elsevier B.V. All rights reserved.

A catalytically active nanoassembly comprising Cu-nanoparticles grown on integrated and active supports (large pore Zr-doped mesoporous SBA-15 silica) has been synthesized and used to promote CO2 hydrogenation. The doped mesoporous material was synthesized using a sal-gel method, in which the pore size was tuned between 11 and 15 nm while maintaining a specific surface area of about 700 m(2) g (1). The subsequent Cu nanoparticle growth was achieved by an infiltration process involving attachment of different functional groups on the external and internal surfaces of the mesoporous structure such that 7-10 nm sized Cu nanoparticles grew preferentially inside the pores. Chemisorption showed improved absorption of both CO2 and H-2 for the assembly compared to pure SBA-15 and 15% of the total CO2 was converted to methanol and dimethyl ether at 250 degrees C and 33 bar.

In this laboratory experiment, students learn how to synthesize mesoporous silica of the SBA-15 type and explore how the different synthesis steps affect the final material. Mesoporous materials, especially SBA-15, are often used in the development of new methods for. drug delivery, catalysis, and separation because of the flexibility of tailoring these materials to optimize the performance in different applications. However, the synthesis of mesoporous materials is rarely introduced to undergraduate students. The material synthesis is a simple sol gel process, where small alterations in the synthesis steps can significantly change the material characteristics. The presented laboratory experiment aims to introduce undergraduate students to the synthesis of SBA-15 mesoporous silica with different pore sizes due to alterations in the hydrothermal treatment time and/ or temperature and to give students hands-on experience with important characterization tools, including physisorption, X-ray diffraction, FTIR spectroscopy, and thermogravimetric analysis, to understand the effect of hydrothermal treatment and surfactant removal. Additional synthesis parameters to study, such as surfactant removal, the silica precursor, and pore swelling agents, are also presented. The experiment has been used in teaching of both bachelors and masters students and can be adapted to various instrumental techniques, e.g., scanning electron microscopy for morphology studies, transition electron microscopy for pore structure characterization, etc.

In this study, mesoporous silica nanoparticles (MSPs) of different size and shape were developed, and their surface coatings were utilized to study their differential effects in enhancing antibacterial activity. In brief, MSPs with three different aspect ratios (1, 2 and 4) were prepared, doped with silver ions and finally coated with the polymer chitosan. Both Gram-positive and Gram-negative bacteria were treated with the MSPs. Results indicate that silver ion doped and chitosan coated MSPs with the aspect ratio of 4 (Cht/MSP4:Ag+) have the highest antimicrobial activity among the prepared series. Further studies revealed that Cht/MSP4:Ag+ was most effective against Escherichia coli (E.coli) and least effective against Vibrio cholerae (V. cholerae). To investigate the detailed inhibition mechanism of the MSPs, the interaction of the nanoparticles with E.coli membranes and its intracellular DNA was assessed using various spectroscopic and imaging-based techniques. Furthermore, to increase the efficiency of the MSPs, a combinatorial antibacterial strategy was also explored, where nanoparticles, in combination with kanamycin (antibiotic), were used against Vibrio Cholerae (V. cholerae). Toxicity screening of these on MSPs was conducted on Caco-2 cells, and the results show that the dose used for antibacterial screening is below the limit of the toxicity threshold. Our findings show that both shape and surface engineering contribute positively towards killing bacteria, and the newly developed silver ion-doped and chitosan-coated MSPs have good potential as antimicrobial nanomaterials.

The catalytic properties of 3 types of mesoporous silica SBA-15 (rope, rod and fiber), with 9.2 nm or 12.1 nm large mesopores, were examined with respect to their morphology and pore size. Commercially available Amberlyst-15 and the small pore sized MCM-41 were used for comparison. The catalysts were prepared by functionalization of the silica supports with propylsulfonic acid (Pr-SO3H) using postsynthesis grafting with 3 -mercaptopropyltrimethoxysilane as a propyl-thiol precursor. All materials remained in a well-ordered hexagonal mesoporous structure after Pr-SO3H functionalization. The performance of the Pr-SO3H-functionalized mesoporous silicas was evaluated in terms of their catalytic activity in the esterification of oleic acid with short (methanol) and long (glycerol) chain alcohols, i.e., to test the effect of the pore size on the substrate conversion and product yield. The synthesized catalysts were highly active and the product composition could be tuned by selective choice of the mesopore size. The Pr-SO3H-functionalized rope-shaped SBA-15 gave the highest catalytic activity (in terms of the highest methyl oleate and triglyceride yields and oleic acid conversion level), which was higher than that obtained with the commercial Amberlyst-15 catalyst. A high acid amount, large specific surface area and a suitable pore size are the likely reasons for the high yield gained by Pr-SO3H-functionalized rope-shaped SBA-15 silica. (C) 2015 Elsevier B.V. All rights reserved.

Targeted cancer therapies are currently a strong focus in biomedical research. The most common approach is to use nanocarrier-based targeting to specifically deliver conventional anticancer drugs to enhance their therapeutic efficacy, increase bioavailability, and decrease the side-effects on normal cells. A step further towards higher specificity and efficacy would be to employ specific novel drugs along with specific nanocarrier-based targeting. Our recent studies have demonstrated that a plant-derived diterpenoid compound, anisomelic acid (AA), induces apoptosis in cervical cancer cells. In this work, we describe the development of a folic acid (FA)-targeted AA delivery system using chitosan-coated rod-shaped mesoporous silica particles (Chitosan-NR-MSP). The cellular internalization and uptake enhancement of the FA-Chitosan-NR-MSP towards cancerous folate receptor (FR)-positive (SiHa and HeLa) and/or normal FR-negative (HEK 293) cells were assessed, which indicated that the intracellular uptake of FA-conjugated Chitosan-NR-MSP was more target-specific. Furthermore, the induction of apoptosis by AA-loaded chitosan-coated rod-shaped particles on SiHa cells was studied. By employing caspase-3 activation and PARP cleavage as measure of apoptosis, the FA-particle mediated AA treatment was clearly more effective, significantly enhancing apoptosis in comparison to non-targeted Chitosan-NR-MSP or free AA in SiHa cells, suggesting that the FA-Chitosan-NR-MSPs can be potentially utilized as a drug delivery system for cervical cancer treatment.

Mesoporous silica films consisting of a monolayer of separated SBA-15 particles with unusually wide and short pores grown on silicon wafers have been fabricated in a simple single-pot-synthesis, and the formation of the films has been studied. A recipe for synthesizing mesoporous silica rods with the addition of heptane and NH₄F at low temperature was used and substrates were added to the synthesis solution during the reaction. The films are ∼90 nm thick, have a pore size of 10.7–13.9 nm depending on the hydrothermal treatment time and temperature, and a pore length of 200–400 nm. All pores are parallel to the substrate, open, and easy to access, making them suitable for applications such as catalyst hosts and gas separation. The growth of the films is closely correlated to the evolution of the mesoporous silica particles. Here, we have studied the time for adding substrates to the synthesis solution, the evolution of the films with time during formation, and the effect of hydrothermal treatment. It was found that the substrates should be added within 30–60 s after turning off the stirring and the films are formed within 10 min after addition to the synthesis solution. The study has yielded a new route for synthesizing mesoporous silica films with a unique morphology.

A method for synthesizing mesoporous silica films with cylindrical pores perpendicular to the substrate has been developed. The films consist of SBA-15 platelets that are grafted on glass substrates. The grafting is studied in terms of parameters such as pH, substrate functionalization, salt additions, time for TEOS prehydrolysis, and calcination. The best coverage of particles on the substrate was achieved for a low pH in combination with OTS-treated glass substrate. Furthermore, the prehydrolysis time of the TEOS was found to be a key parameter in order to bind the particles to the substrate. These porous films have potential in applications such as catalysis, drug delivery, and as a template for nanoparticle or nanorod, growth.

Catalyst supports, drug delivery systems, hosts for nanoparticles, and solar cells are just some examples of the wide range of exciting applications for mesoporous silica. In order to optimize the performance of a specific application, controlling the material’s morphology and pore size is crucial. For example, short and separated particles are beneficial for drug delivery systems, while for molecular sieves, the pore size is the key parameter.

In this thesis, mesoporous silica building blocks, crystallites, with hexagonally ordered cylindrical pores were synthesized, with the aim to understand how the synthesis parameters affect the particle morphology and pore size. The synthesis of the particles is performed using a sol-gel process, and in order to increase the pore size, a combination of low temperature, and additions of heptane and NH4F was used. By variations in the amounts of reagents, as well as other synthesis conditions, the particle morphology and pore size could be altered. Separated particles were also grown on or attached to substrates to form films. Also, a material with spherical pore structure was synthesized, for the first time using this method.

It was found that a variation in the heptane concentration, in combination with a long stirring time, yields a transition between fiber and sheet morphologies. Both morphologies consist of crystallites, which for the fibers are joined end to end, while for the sheets they are attached side by side such that the pores are accessible from the sheet surface. The crystallites can be separated to a rod morphology by decreasing the stirring time and tuning the HCl concentration, and it was seen that these rods are formed within 5 min of static time, even though the pore size and unit cell parameters were evolving for another 30 min. Further studies of the effects of heptane showed that the shape and mesoscopic parameters of the rods are affected by the heptane concentration, up to a value where the micelles are fully saturated with heptane. It was also observed that the particle width increases with decreasing NH4F concentration, independent of heptane amount, and a platelet morphology can be formed. The formation time of the particles decrease with decreasing NH4F, and the growth mechanism for platelets was further studied. The pore sizes for various morphologies were altered by e.g. variations in the hydrothermal treatment conditions, or the method for removing the surfactants.

The separated particles can be attached to substrates, either during the particle synthesis or by post grafting prior to calcination. The film formation during the one-pot-synthesis was studied and a formation mechanism including nucleation of elongated micelles on the substrate was suggested. During the post grafting film synthesis, the medium in which the particles are dispersed, as well as functionalization of both particle and substrate are crucial for the post grafting process. The pores are easily accessible independent of the method, even though they are aligned parallel to the substrate when the one-pot-method is used, while post grafting gives a perpendicular pore orientation.

In summary, this work aims to give an understanding for the formation of the synthesized material, and how to tune the material properties by alterations in parameter space. Successful syntheses of four different particle morphologies and two new types of films were performed, and the pore size could easily be tuned by various methods.

The knowledge of how to control the pore size and morphology of separated mesoporous silica particles is crucial for optimizing their performance in applications, such as molecular sieves and drug delivery systems. In this work, we have systematically studied the effects of various synthesis parameters to gain a deeper understanding of how particle morphologies can be altered. It was found that the morphology for isolated particles of SBA-15 type, with unusually short and wide pores, could be altered from rods to platelets by variations in the NH4F concentration. The pore length is nearly constant (similar to 300 nm) for the different morphologies, but the particle width is increasing from 200 nm to >3 mu m when decreasing the amount of NH4F, and the pore size can be tuned between 10 and 13 nm. Furthermore, other synthesis parameters such as heptane concentration, pH, silica precursor, and additions of ions have also been studied. The trend regarding particle width is independent of heptane concentration, at the same time as heptane increases the particle length up to a plateau value of similar to 500 nm. In all, parameters controlling particle width, length, and pore size have been separated in order to evaluate their function in the particle formation. Additionally, it was found that the formation time of the particles is strongly affected by the fluoride ion concentration, and a mechanism for particle formation for this system, where micelles transform from a foam, to multilamellar vesicles, and finally to cylindrical micelles, is suggested.

Immobilization of enzymes usually improves the recyclability and stability and can sometimes also improve the activity compared to enzymes free in solution. Mesoporous silica is a widely studied material as host for immobilized enzymes because of its large internal surface area and tunable pores. It has previously been shown that the pore size is critical both for the loading capacity and for the enzymatic activity; however, less focus has been given to the influence of the particle size. In this work the effect of particle size and particle morphology on the immobilization of lipase from Mucor miehei and Rhizopus oryzae have been investigated. Three kinds of mesoporous silica, all with 9 nm pores but with varying particle size (1000 nm, 300 nm and 40 nm) have been synthesized and were used as host for the lipases. The two lipases, which have the same molecular size but widely different isoelectric points, were immobilized into the silica particles at varied pH values within the interval 5 to 8. The 300 nm particles were proven to be the most suitable carrier with respect to specific activity for both enzymes. The lipase from Mucor miehei was more than four times as active when immobilized at pH 8 compared to free in solution whereas the difference was less pronounced for the Rhizopus oryzae lipase.

Iron oxide (α-Fe₂O₃) nanoparticles with very small size, high crystallinity, and narrow size distribution were synthesized by infiltration of Fe(NO₃)₃.9H₂O as an oxide precursor into mesoporous silica (SBA-15 and SBA-16) molds using a wetimpregnation technique. High resolution transmission electron microscopy shows that during the hydrothermal treatment of the precursor at 140 °C for 2 days, stable α-Fe₂O₃ nanoparticles inside the silica pores are formed. Subsequent leaching out of the silica template by NaOH resulted in well dispersed nanoparticles with an average diameter of ~ 4 nm.

In nanomedicine, physicochemical properties of the nanocarrier affect the nanoparticles pharmacokinetics and biodistribution, which are also decisive for the passive targeting and nonspecific cellular uptake of nanoparticles. Size and surface charge are, consequently, two main determining factors in nanomedicine applications. Another important parameter which has received much less attention is the morphology (shape) of the nanocarrier. In order to investigate the morphology effect on the extent of cellular internalization, two similarly sized but differently shaped rod-like and spherical mesoporous silica nanoparticles were synthesized, characterized and functionalized to yield different surface charges. The uptake in two different cancer cell lines was investigated as a function of particle shape, coating (organic modification), surface charge and dose. According to the presented results, particle morphology is a decisive property regardless of both the different surface charges and doses tested, whereby rod-like particles internalized more efficiently in both cell lines. At lower doses whereby the shape-induced advantage is less dominant, charge-induced effects can, however, be used to fine-tune the cellular uptake as a prospective secondary uptake regulator for tight dose control in nanoparticle-based drug formulations.

Phase transformations during annealing of coatings sprayed with the High Velocity Oxy-Fuel technique using Ti₂AlC powder have been investigated by in-situ x-ray diffraction. The asdeposited coatings, consisting of Ti2AlC, Ti₃AlC₂, TiC, Ti-Al, and oxides, are stable up to 500 °C. Ti3AlC2 forms above 550 °C and Ti₂AlC forms above 700 °C by intercalation of Al into TiC_x. For temperatures between 900 and 1100 °C, Ti₃AlC₂ and Ti₂AlC decompose by losing Al to the surrounding matrix resulting in TiCx, and Al₂O₃. The thermal expansion coefficient between ambient and 700°C is 11.9·10^-6 K^-1. The thermal diffusivity at room temperature is 1.9·10^-6 m²/s.

A solution based wet chemistry approach has been developed for synthesizing Li(2)SiO(3) using LiNO(3) and mesoporous silica as starting materials at 550 degrees C. A reaction path where NO and O(2) are formed as side-products is proposed. The crystals synthesized exhibit dendritic growth where the as-prepared nanodendrite is a typical 1-fold nanodendrite composed of one several microns long and some tenth of nanometers wide trunk with small branches, which are several hundreds of nanometers long and up to 70 nm in diameter. The effect of the structure of the mesoporous silica for the final morphology is discussed.

Dispersed SBA-15 rods have been synthesized with varying lengths, widths, and pore sizes in a low-temperature synthesis in the presence of heptane and NH4F. The pore size of the material can systematically be varied between 11 and 17 nm using different hydrothermal treatment times And/or temperatures. The particle length (400-600 nm) and width (100-400 nm) were tuned by varying the HCl concentration. All the synthesized materials possess a large surface area of 400-600 m(2)/g And a pore volume of 1.05-1.30 cm(3). A, mechanism for the effect of the HCl concentration on the particle morphology is suggested. Furthermore, it is shown that the reaction time an be decreased to 1 h, with well-retained pore size and morphology. This work has resulted in SBA-15 rods with the largest pore size reported for this morphology.

The synthesis of spherical copper nanoparticles with extremely narrow size distribution by electroless copper deposition on mesoporous silica support is described. The materials were characterized by nitrogen sorption, transmission electron microscopy, x-ray diffractometry and Fourier transform infrared spectroscopy. The copper nanoparticles have a cubic crystalline structure and an average particle size of 5.5 +/- 0.8 nm. The copper nanoparticles are stable, without detectable oxidation or further agglomeration under ambient conditions even after months. These results demonstrate that electroless copper reduction can be conducted and constrained within the mesoporous silica framework, which pave the way for engineered mesoreactors.

Hollow silica SBA-16 spheres with cubic ordered mesoporous shells were synthesized by an emulsion-templating method, using Pluronic F127 as a structure-directing agent. tetraethyl orthosilicateas as a silica source and heptane as a cosolvent in the presence of NH4F. The size of these spheres is in the range of 10 to 30 mu m. The shell is about 700 nm thick and consists of large pores, similar to 9 nm in diameter, arranged in a cubic order. After calcination, the spheres maintain their mesoporosity and show a high surface area of 822 m(2)/g. The formation mechanism of the silica hollow spheres is discussed.

Mesoporous silica with a hexagonally ordered pore structure (SBA-15) has been synthesized. Through variations in the synthesis conditions several morphologies, such as fibers, sheets and separate rods, have been realized. Furthermore, additions of heptane and NH4F make it possible to synthesize SBA-15 with pores as large as 18 nm in the sheet morphology. Mechanisms for the formation of different morphologies have been suggested. In the case of fibers and sheets, the amount of heptane present during the synthesis determines the final morphology. For low concentrations, the heptane enters the micelles and increases the pore size while the particles (crystallites) attaches to each other end to end. When the heptane concentration increases, the heptane droplets increase in size, and above a critical droplet size the crystallites attach with one short end towards the droplet, forming the sheet morphology. The crystallites can also be separated. This is the case of the rod morphology. The separation is performed by shortening the stirring time and increasing the HCl concentration. The increased amount of HCl increases the hydration rate of the silica precursor, which can be used to control the thickness and length of the rods. Furthermore, the reaction time has been decreased from 20 h for all morphologies to less than 4 hours. The materials have been characterized with nitrogen sorption, electron microscopy and x-ray diffraction. Also, thermogravimetric analysis and fourier transformed infrared spectroscopy have been used for studying the removal of surfactants.

The effect of heptane on the particle morphology and pore size in the synthesis of SBA-15 is presented. Heptane in the presence of NH4F works as a pore swelling agent, resulting in 13-18 nm sized pores in 400 nm long and 200-1000 nm wide crystallites. The pores are hexagonally arranged and run through the crystallites. Increasing the heptane to P123 molar ratio changes the morphology of SBA-15 from fibers to sheets when the crystallites rearrange during the synthesis. The pore order in the sheets is controlled by changing the molar ratio of water to P123. The surface areas of these materials are 500-800 m(2)/g with pore volumes of 1.2-1.7 cm(3)/g. The sheets have accessible pores with a size of 18 nm running parallel to the sheet normal, which makes them suitable for membranes.

Mesoporous silica SBA-15 in the form of 10-30 μm sized sheets with unusually large ordered pores has been synthesized using heptane as a cosolvent in the presence of NH4F. The resulting morphology of 400 nm thick sheets that contain easily accessed, hexagonally arranged, 18 nm sized pores running parallel to sheet normal has not been previously reported. The material has a BET surface area of 541 m2/g, large pore volume of 1.69 cm3/g and ordered mesopore structure with a narrow pore size distribution around 18 nm. A mechanism for sheet formation based on heptane droplets acting as sites for self assembling of silica crystallites is suggested.