Photon energy upconversion, i.e. the conversion of several low-energy photons to a photon of higher energy, offers significant potential for nano-optoelectronics and nanophotonics applications. The primary challenge is to achieve high upconversion efficiency and a broad device performance range, enabling effective upconversion even at low excitation power. This study demonstrates that core/shell semiconductor nanowire heterostructures can exhibit upconversion efficiencies exceeding what was previously reported for semiconductor nanostructures even at a low excitation power of 100 mW/cm2, by a two-photon absorption process through conduction band states of the narrow-bandgap nanowire shell region. By engineering the electric-field distribution of the excitation light inside the NWs, upconversion efficiency can be further improved by eight times. This work showcases the effectiveness of the proposed approach in achieving efficient photon upconversion using core/shell NW heterostructures, resulting in some of the highest upconversion efficiencies reported in semiconductor nanostructures. Additionally, it offers design guidelines for enhancing energy upconversion efficiency.

β-Ga2O3 is a wide bandgap semiconductor that is attractive for various applications, including power electronics, transparent conductive electrodes, etc. Electrical and optical properties of Ga2O3 are affected by the presence of dopants/contaminants and/or intrinsic defects. Here, we investigate the electrical and optical properties of transition metals like Co and Cr since they are often unintentionally present during the growth or used as intentional dopants. This is done by using magnetic resonance spectroscopy and magneto-optical characterization techniques. We determine spin- Hamiltonian parameters of the Cr3+ ground-state and first excited-state as well as the spin-Hamiltonian parameters of Co2+.

Lignin, a byproduct from the pulp industry, is one of the redox active biopolymers being investigated as a component in the electrodes for sustainable energy storage applications. Due to its insulating nature, it needs to be combined with a conductor such as carbon or conducting polymer for efficient charge storage. Here, the lignin/carbon composite electrodes manufactured via mechanical milling (ball milling) are reported. The composite formation, correlation between performance and morphology is studied by comparison with manual mixing and jet milling. Superior charge storage capacity with approximate to 70% of the total contribution from the Faradaic process involving the redox functionality of lignin is observed in a mechanically milled composite. In comparison, manual mix shows only approximate to 30% from the lignin storage participation while the rest is due to the electric double layer at the carbon-electrolyte interface. The significant participation of lignin in the ball milled composite is attributed to the homogeneous, intimate mixing of the carbon and the lignin leading the electronic carrier transported in the carbon phase to reach most of the redox group of lignin. A maximum capacity of 49 mAh g(-1) is obtained at charge/discharge rate of 0.25 A g(-1) for the sample milled for 60 min.

Energy upconversion via optical processes in semiconductor nanowires (NWs) is attractive for a variety of applications in nano-optoelectronics and nanophotonics. One of the main challenges is to achieve a high upconversion efficiency and, thus, a wide dynamic range of device performance, allowing efficient upconversion even under low excitation power. Here, we demonstrate that the efficiency of energy upconversion via two-photon absorption (TPA) can be drastically enhanced in core/shell NW heterostructures designed to provide a real intermediate TPA step via the band states of the narrow-bandgap region with a long carrier lifetime, fulfilling all the necessary requirements for high-efficiency two-step TPA. We show that, in radial GaAs(P)/GaNAs(P) core/shell NW heterostructures, the upconversion efficiency increases by 500 times as compared with that of the constituent materials, even under an excitation power as low as 100 mW/cm2 that is comparable to the 1 sun illumination. The upconversion efficiency can be further improved by 8 times through engineering the electric-field distribution of the excitation light inside the NWs so that light absorption is maximized within the desired region of the heterostructure. This work demonstrates the effectiveness of our approach in providing efficient photon upconversion by exploring core/shell NW heterostructures, yielding an upconversion efficiency being among the highest reported in semiconductor nanostructures. Furthermore, our work provides design guidelines for enhancing efficiency of energy in NW heterostructures.

We report on optimization of growth conditions of GaAs/GaNAs/GaAs core/shell/shell nanowire (NW) structures emitting at ~1 μm, aiming to increase their light emitting efficiency. A slight change in growth temperature is found to critically affect optical quality of the active GaNAs shell and is shown to result from suppressed formation of non-radiative recombination (NRR) centers under the optimum growth temperature. By employing the optically detected magnetic resonance spectroscopy, we identify gallium vacancies and gallium interstitials as being among the dominant NRR defects. The radiative efficiency of the NWs can be further improved by post-growth annealing at 680 °C, which removes the gallium interstitials.

Nanowires (NWs) based on ternary GaAsP and quaternary GaNAsP alloys are considered as very promising materials for optoelectronic applications, including in multi-junction and intermediate band solar cells. The efficiency of such devices is expected to be largely controlled by grown-in defects. In this work we use the optically detected magnetic resonance (ODMR) technique combined with photoluminescence measurements to investigate the origin of point defects in Ga(N)AsP NWs grown by molecular beam epitaxy on Si substrates. We identify gallium vacancies, which act as non-radiative recombination centers, as common defects in ternary and quaternary Ga(N)AsP NWs. Furthermore, we show that the presence of N is not strictly necessary for, but promotes, the formation of gallium vacancies in these NWs.

Nanostructured III-V semiconductors have emerged as one of the most promising materials systems for future optoelectronic applications. While planar III-V compounds are already at the center of the ongoing lighting revolution, where older light sources are replaced by modern white light LEDs, fabricating such materials in novel architectures, such as nanowires and quantum dots, creates new possibilities for optoelectronic applications. Not only do nanoscale structures allow the optically active III-V materials to be integrated with silicon microelectronics, but they also give rise to new fascinating properties inherent to the nanoscale.

One of the key parameters considered when selecting materials for applications in light-emitting and photovoltaic devices is the band gap energy. While alloying of conventional III-V materials provides a certain degree of band gap tunability, a significantly enhanced possibility of band gap engineering is offered by so-called dilute nitrides, where incorporation of a small percentage of nitrogen into III-V compounds causes a dramatic down-shift of the conduction band edge. In addition, nitrogen-induced splitting of the conduction band in dilute nitrides can be utilized in intermediate band solar cells, belonging to the next generation of photovoltaic devices.

For any material to be viable for optoelectronic applications, detailed knowledge of the electronic structure of the material, as well as a good understanding of carrier recombination processes is vital. For example, alloying may not only cause changes in the electronic structure but can also induce disorder. Disorder-induced potential fluctuations may alter charge carrier and exciton dynamics, and may even induce quantum confinement. Moreover, various defects in the material may introduce detrimental non-radiative (NR) states in the band gap deteriorating radiative efficiency. It is evident that, due to their different growth mechanisms, such properties could be markedly different in nanowires as compared to their planar counterparts. In this thesis, I aim to describe the electronic structure of dilute nitride nanowires, and its effects on the optical properties. Firstly, we investigate the electronic structure, and the structural and optical properties of novel GaNAsP nanowires, with a particular focus on the dominant recombination channels in the material. Secondly, we show how short-range fluctuations in the nitrogen content lead to the formation of quantum dots in dilute nitride nanowires, and investigate their electronic structure. Finally, we investigate the combined charge carrier and exciton dynamics of the quantum dots and effects of defects in their surroundings.

Before considering individual sources of NR recombination, it is instructive to investigate the overall effects of nitrogen incorporation on the structural properties of the nanowires. In Paper I, we show that nitrogen incorporation up to 0.16\% in Ga(N)AsP nanowires does not affect the overall structural quality of the material, nor does nitrogen degrade the good compositional uniformity of the nanowires. It is evident from our studies, however, that nitrogen incorporation has a strong and complex effect on recombination processes. We first show that nitrogen incorporation in GaNAsP nanowires reduces the NR recombination at room temperature as compared to the nitrogen-free nanowires (Paper I). This is in stark contrast to dilute nitride epilayers, where nitrogen incorporation enhances NR recombination. The reason for this difference is that in nanowires the surface recombination, rather than recombination via point defects, is the dominant NR recombination mechanism. We suggest that the nitrogen-induced suppression of the NR surface recombination in the nanowires is due to nitridation of the nanowire surface.

Another NR recombination channel common in III-V nanowires is caused by the presence of structural defects, such as rotational twin planes and stacking faults. Interestingly, while nitrogen incorporation does not appear to affect the density of such structural defects, increasing nitrogen incorporation reduces the NR recombination via the structural defects (Paper II). This is explained by competing trapping of excited carriers/excitons to the localized states characteristic to dilute nitrides, and at nitrogen-induced NR defects. This effect is, however, only present at cryogenic temperatures, while at room temperature the NR recombination via the structural defects is not the dominant recombination channel.

Importance of point defects in carrier recombination is highlighted in Paper III. Using the optically detected magnetic resonance technique, we show that gallium vacancies (V_Ga) that are formed within the nanowire volume act as efficient NR recombination centers, degrading optical efficiency of the Ga(N)AsP-based nanowires. Interestingly, while the defect formation is promoted by nitrogen incorporation, it is also readily present in ternary GaAsP nanowires. This contrasts with previous studies on planar structures, where V_Ga was not formed in the absence of nitrogen, unless subjected to irradiation by high-energy particles or heavy n-type doping. This, again, highlights how the defect formation is strikingly different in nanowires as compared to planar structures, likely due to the different growth processes.

Potential fluctuations in the conduction band, caused by non-uniformity of the nitrogen incorporation, is characteristic to dilute nitrides and is known to cause exciton/carrier localization. We find that in dilute nitride nanowires, such fluctuations at the short range cause three-dimensional quantum confinement of excitons, resulting in optically active quantum dots with spectrally ultranarrow and highly polarized emission lines (Paper IV). A careful investigation of such quantum dots reveals that their properties are strongly dependent on the host material (Papers V, VI). While the principal quantization axis of the quantum dots formed in the ternary GaNAs nanowires is preferably oriented along the nanowire axis (Paper V), it switches to the direction perpendicular to the nanowire axis in the quaternary GaNAsP nanowires (Paper VI). Another aspect illustrating the influence of the host material on the quantum-dot properties is the electronic character of the captured hole. In both alloys, we show coexistence of quantum dots where the captured holes are of either a pure heavy-hole character or a mixed light-hole and heavy-hole character. In the GaNAs quantum dots, the main cause of the light- and heavy-hole splitting is uniaxial tensile strain induced by a combination of lattice mismatch with the nanowire core and local alloy fluctuations (Paper V). In the GaNAsP quantum dots, however, we suggest that the main mechanism for the light- and heavy-hole splitting is local fluctuations in the P/As ratio (Paper VI).

Using time correlation single-photon counting, we show that the quantum dots in these dilute nitride nanowires behave as single photon emitters (Paper VI), confirming the three-dimensional quantum confinement of the emitters. Finally, since the quantum dots are formed by fluctuations mainly in the conduction band, only electrons are preferentially captured in the 0D confinement potential, whereas holes are expected to be mainly localized through the Coulomb interaction once an electron is captured by the quantum dot. In Paper VII, we investigate this rather peculiar capture mechanism, which we show to lead to unipolar, negative charging of the quantum dot. Moreover, we demonstrate that carrier capture by some quantum dots is strongly affected by the presence of defects in their local surroundings, which further alters the charge state of the quantum dot, where formation of the negatively charged exciton is promoted at the expense of its neutral counterpart. This underlines that the local surroundings of the quantum dots may greatly affect their properties and illustrates a possible way to exploit the defects for charge engineering of the quantum dots.

In summary, in this thesis work, we identify several important non-radiative recombination processes in dilute nitride nanowires that can undermine the potential of these novel nanostructures for future optoelectronic applications. The gained knowledge could be found useful for designing strategies to mitigate these harmful processes, thereby improving the efficiency of future light-emitting and photovoltaic devices based on these nanowires. Furthermore, we uncover a set of optically bright quantum dot single-photon emitters embedded in the dilute nitride nanowires, and reveal their unusual electronic structure with strikingly different confinement potentials between electrons and holes. Our findings open a new pathway for charge engineering of the quantum dots in nanowires, attractive for applications in e.g. quantum computation and optical switching.

In this work we present a significant advancement in cubic silicon carbide (3C-SiC) growth in terms of crystal quality and domain size, and indicate its potential use in photovoltaics. To date, the use of 3C-SiC for photovoltaics has not been considered due to the band gap of 2.3 eV being too large for conventional solar cells. Doping of 3C-SiC with boron introduces an energy level of 0.7 eV above the valence band. Such energy level may form an intermediate band (IB) in the band gap. This IB concept has been presented in the literature to act as an energy ladder that allows absorption of sub-bandgap photons to generate extra electron-hole pairs and increase the efficiency of a solar cell. The main challenge with this concept is to find a materials system that could realize such efficient photovoltaic behavior. The 3C-SiC bandgap and boron energy level fits nicely into the concept, but has not been explored for an IB behavior. For a long time crystalline 3C-SiC has been challenging to grow due to its metastable nature. The material mainly consists of a large number of small domains if the 3C polytype is maintained. In our work a crystal growth process was realized by a new approach that is a combination of initial nucleation and step-flow growth. In the process, the domains that form initially extend laterally to make larger 3C-SiC domains, thus leading to a pronounced improvement in crystalline quality of 3C-SiC. In order to explore the feasibility of IB in 3C-SiC using boron, we have explored two routes of introducing boron impurities; ion implantation on un-doped samples and epitaxial growth on un-doped samples using pre-doped source material. The results show that 3C-SiC doped with boron is an optically active material, and thus is interesting to be further studied for IB behavior. For the ion implanted samples the crystal quality was maintained even after high implantation doses and subsequent annealing. The same was true for the samples grown with pre-doped source material, even with a high concentration of boron impurities. We present optical emission and absorption properties of as-grown and boron implanted 3C-SiC. The low-temperature photoluminescence spectra indicate the formation of optically active deep boron centers, which may be utilized for achieving an IB behavior at sufficiently high dopant concentrations. We also discuss the potential of boron doped 3C-SiC base material in a broader range of applications, such as in photovoltaics, biomarkers and hydrogen generation by splitting water. (C) 2015 Elsevier B.V. All rights reserved.

There is a strong and growing worldwide research on exploring renewable energy resources. Solar energy is the most abundant, inexhaustible and clean energy source, but there are profound material challenges to capture, convert and store solar energy. In this work, we explore 3C-SiC as an attractive material towards solar-driven energy conversion applications: (i) Boron doped 3C-SiC as candidate for an intermediate band photovoltaic material, and (ii) 3C-SiC as a photoelectrode for solar-driven water splitting. Absorption spectrum of boron doped 3C-SiC shows a deep energy level at ~0.7 eV above the valence band edge. This indicates that boron doped 3C-SiC may be a good candidate as an intermediate band photovoltaic material, and that bulk like 3C-SiC can have sufficient quality to be a promising electrode for photoelectrochemical water splitting. © 2016 Trans Tech Publications, Switzerland.

Recent developments in fabrication techniques and extensive investigations of the physical properties of III-V semiconductor nanowires (NWs), such as GaAs NWs, have demonstrated their potential for a multitude of advanced electronic and photonics applications. Alloying of GaAs with nitrogen can further enhance the performance and extend the device functionality via intentional defects and heterostructure engineering in GaNAs and GaAs/GaNAs coaxial NWs. In this work, it is shown that incorporation of nitrogen in GaAs NWs leads to formation of three-dimensional confining potentials caused by short-range fluctuations in the nitrogen composition, which are superimposed on long-range alloy disorder. The resulting localized states exhibit a quantum-dot like electronic structure, forming optically active states in the GaNAs shell. By directly correlating the structural and optical properties of individual NWs, it is also shown that formation of the localized states is efficient in pure zinc-blende wires and is further facilitated by structural polymorphism. The light emission from these localized states is found to be spectrally narrow (similar to 50-130 mu eV) and is highly polarized (up to 100%) with the preferable polarization direction orthogonal to the NW axis, suggesting a preferential orientation of the localization potential. These properties of self-assembled nano-emitters embedded in the GaNAs-based nanowire structures may be attractive for potential optoelectronic applications.