liu.seSearch for publications in DiVA
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
CFD Simulations of Skip Movements in Mine Shafts
Linköping University, Department of Management and Engineering, Applied Thermodynamics and Fluid Mechanics.
2026 (English)Independent thesis Advanced level (degree of Master (Two Years)), 20 credits / 30 HE creditsStudent thesis
Abstract [en]

In deep-shaft hoisting, rope guides provide an alternative to fixed rigid guides: the skips are held laterally only by the flexibility of their suspension ropes rather than by rigid rails. When two counterbalanced skips pass one another at high speed near mid-shaft, the air displaced through the narrowing gap generates transient aerodynamic forces that drive the conveyances laterally, raising the risk of conveyance-to-wall or conveyance-to-conveyance contact. Predicting this lateral sway is central to safe clearance design, yet prior numerical work has been confined either to two dimensions or to three-dimensional models that suffer near-wall mesh degradation over the transit and rely on linear rope-stiffness approximations; the behaviour over a complete, high-speed transit in three dimensions had not been demonstrated.This thesis develops a three-dimensional transient fluid–structure interaction (FSI) methodology for the skip passing event. The turbulent flow is modelled with the URANS k–ω SST closure, and a dynamic-meshing strategy combining unified remeshing, diffusion smoothing, and a rigidly translated near-wall layer sustains a stable, converged solution over the full hoisting depth without near-wall degradation. Greenway's non-linear, depth-dependent rope-stiffness formulation is embedded in the coupling through a custom user-defined function, replacing the linear-spring idealisations of earlier studies. The work is methodological and exploratory in character: it develops and tests a simulation capability rather than validating against site measurements or certifying a clearance for a specific installation.

Two reduced-cost alternatives to the fully coupled model were assessed, and neither proved adequate. A two- to three-dimensional force correction factor could not be defined: on a fixed centreline the two- and three-dimensional lateral forces reverse in sign, so no consistent scalar ratio can reconcile them. A one-way decoupled coupling reproduces the coupled solution only while lateral displacements remain small and progressively under-predicts as the amplitude grows; because its validity is bounded by the very amplitude it is used to predict, it cannot certify its own range of validity, and its under-prediction overstates the available clearance, an error in the unsafe direction. Two-way coupling is therefore adopted as the design authority throughout.

Applied to two full-depth configurations, an 850 m reference shaft and a 1680 m deep shaft, the model shows the lateral response to be set by two largely independent factors. The aerodynamic forcing scales with the velocity of each conveyance relative to the ventilation air, so that the skip traveling against the airflow is the more severely loaded; the empty descending skip therefore dominates under upcast ventilation and the loaded ascending skip under downcast, a reversal isolated by a ventilation sub-study at fixed geometry. The depth-dependent rope stiffness sets where the response peaks: the largest excursions develop not at the passing event but in the compliant mid-to-lower shaft, where the combined rope stiffness passes through a broad minimum. Among the geometric parameters, the shaft bore diameter is the dominant influence, acting purely aerodynamically by enlarging the annular flow area; inter-skip spacing acts weakly and inconsistently, and a local passing-zone widening fails to relieve the sway and can worsen it for the empty conveyance.

Place, publisher, year, edition, pages
2026. , p. 91
Keywords [en]
Fluid–structure interaction, CFD, Mine hoisting, Rope-guided skip, Lateral sway, Dynamic mesh
National Category
Fluid Mechanics Applied Mechanics
Identifiers
URN: urn:nbn:se:liu:diva-228045ISRN: LIU-IEI-TEK-A--26/05520--SEOAI: oai:DiVA.org:liu-228045DiVA, id: diva2:2105535
External cooperation
ABB Corporate Research, Västerås
Subject / course
Aeronautical Engineering
Presentation
2026-09-08, TE-huset, 2B:841, Campus Valla, A-huset, Linköpings universitet, Linköping, Sweden, 10:32 (English)
Supervisors
Examiners
Available from: 2026-09-28 Created: 2026-09-28 Last updated: 2026-09-28Bibliographically approved

Open Access in DiVA

fulltext(5976 kB)60 downloads
File information
File name FULLTEXT01.pdfFile size 5976 kBChecksum SHA-512
3faf37a95b62262de38104faba7efa45a2c648d44a232f7a5b6df72b06f3041c81328abe8d0502675fadac2ba4fa1e7645281803b931153030ee6d33a579b0ba
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Rajesh, Varunn
By organisation
Applied Thermodynamics and Fluid Mechanics
Fluid MechanicsApplied Mechanics

Search outside of DiVA

GoogleGoogle Scholar
Total: 60 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

urn-nbn

Altmetric score

urn-nbn
Total: 666 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • oxford
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf